AMU/IP Telefoni Haderslev Kaserne/SIP Setup/Voice VLAN

From Teknologisk videncenter
Jump to: navigation, search

Oprettelse af VLAN

Før et vlan kan bruges på en switch skal den oprettes først. VLAN 1 findes i forvejen og behøver derfor ikke at blive oprettet.

Switch><input>en</input>
Password:
Switch#<input>configure terminal</input>
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#<input>vlan 200</input>
Switch(config-vlan)#<input>name Voice-VLAN</input>
Switch(config-vlan)#<input>exit</input>
Switch(config)#<input>end</input>
Switch#<input>show vlan brief</input>

VLAN Name                             Status    Ports
---- -------------------------------- --------- -------------------------------
1    default                          active    Fa0/1, Fa0/2, Fa0/3, Fa0/4
                                                Fa0/5, Fa0/6, Fa0/7, Fa0/8
                                                Fa0/9, Fa0/10, Fa0/11, Fa0/12
                                                Fa0/13, Fa0/14, Fa0/15, Fa0/16
                                                Fa0/17, Fa0/18, Fa0/19, Fa0/20
                                                Fa0/21, Fa0/22, Fa0/23, Fa0/24
                                                Gi0/1, Gi0/2
<notice>200  Voice-VLAN                       active    Fa0/1</notice>
1002 fddi-default                     act/unsup
1003 trcrf-default                    act/unsup
1004 fddinet-default                  act/unsup
1005 trbrf-default                    act/unsup
Switch#

Konfigurere Voice port

Her konfigureres porten med Access VLAN 1 og VLAN 200 Voice.

Switch#<input>configure terminal</input>
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#<input>interface fastethernet 0/1</input>
Switch(config-if)#<input>switchport mode access</input>
Switch(config-if)#<input>switchport access vlan 1</input>
Switch(config-if)#<input>switchport voice vlan 200</input>
Switch(config-if)#<input>end</input>
Switch#<input>show interface fastethernet 0/1 switchport</input>
Name: Fa0/1
Switchport: Enabled
Administrative Mode: <notice>static access</notice>
Operational Mode: <notice>static access</notice>
Administrative Trunking Encapsulation: negotiate
Operational Trunking Encapsulation: native
Negotiation of Trunking: Off
Access Mode VLAN: <notice>1 (default)</notice>
Trunking Native Mode VLAN: <notice>1 (default)</notice>
Administrative Native VLAN tagging: enabled
Voice VLAN: <notice>200 (Voice-VLAN)</notice>
Administrative private-vlan host-association: none
Administrative private-vlan mapping: none
Administrative private-vlan trunk native VLAN: none
Administrative private-vlan trunk Native VLAN tagging: enabled
Administrative private-vlan trunk encapsulation: dot1q
Administrative private-vlan trunk normal VLANs: none
Administrative private-vlan trunk associations: none
Administrative private-vlan trunk mappings: none
Operational private-vlan: none
Trunking VLANs Enabled: ALL
Pruning VLANs Enabled: 2-1001
Capture Mode Disabled
Capture VLANs Allowed: ALL

Protected: false
Unknown unicast blocked: disabled
Unknown multicast blocked: disabled
Appliance trust: none
Switch#

Konfiguration af Access Port

Porten hvor IPPBX'en er forbundet skal være statisk konfigureret til access port med access i VLAN 200.

Switch#<input>conf t</input>
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#<input>int fa 0/1</input>
Switch(config-if)#<input>swi mode acc</input>
Switch(config-if)#<input>swi acc vlan 200</input>
Switch(config-if)#<input>end</input>
Switch#

Konfiguration af Management IP

Giv jeres Switch en IP addresse på 192.168.139.0/24 nettet, med ip .11 for gruppe 1, .12 for gruppe 2 osv.

interface Vlan1
 ip address 192.168.139.11 255.255.255.0
!
ip default-gateway 192.168.139.1
ip name-server 172.16.4.66


Kan du nu pinge Switchen fra din computer?

Kan du telnette til den?

  • Konfigurer nu telnet adgang til switchen, ligesom vi lærte i sidste uge.