Wireless LAN Controller 4400/Recovery Example

From Teknologisk videncenter
Jump to: navigation, search
Bootloader 7.0.116.0 (Apr 13 2011 - 14:30:45)

Motorola PowerPC ProcessorID=00000000 Rev. PVR=80200020
        CPU: 833 MHz
        CCB: 333 MHz
        DDR: 166 MHz
        LBC: 41 MHz
L1 D-cache 32KB, L1 I-cache 32KB enabled.
I2C:   ready
DTT:   1 is 33 C
DRAM:  DDR module detected, total size:512MB.
512 MB
8540 in PCI Host Mode.
8540 is the PCI Arbiter.

Memory Test PASS

FLASH:
  Flash Bank 0: portsize = 2, size = 8 MB in 142 Sectors
 8 MB
L2 cache enabled: 256KB
Card Id: 1536
Card Revision Id: 1
Card CPU Id: 1287
Number of MAC Addresses: 32
Number of Slots Supported: 4
Serial Number: FOC1145F076
Unknown command Id: 0xa5
Unknown command Id: 0xa4
Unknown command Id: 0xa3
Manufacturers ID: 30464
Board Maintenance Level: 00
Number of supported APs: 100
In:    serial
Out:   serial
Err:   serial





                      .o88b. d888888b .d8888.  .o88b.  .d88b.
                     d8P  Y8   `88'   88'  YP d8P  Y8 .8P  Y8.
                     8P         88    `8bo.   8P      88    88
                     8b         88      `Y8b. 8b      88    88
                     Y8b  d8   .88.   db   8D Y8b  d8 `8b  d8'
                      `Y88P' Y888888P `8888Y'  `Y88P'  `Y88P'
                    Model AIR-WLC4404-100-K9   S/N: FOC1145F076
Net:
 PHY DEVICE  : Found Intel LXT971A PHY at 0x01
FEC ETHERNET
IDE:   Bus 0: OK
  Device 0: Model: SMART CF Firm: 20060811 Ser#: 00001011710100540124
            Type: Hard Disk
            Capacity: 247.0 MB = 0.2 GB (506016 x 512)
  Device 1: not available

Booting Primary Image...
Press <notice><ESC></notice> now for additional boot options...

***** External Console Active *****



    Boot Options

Please choose an option from below:

 1. Run primary image (version 7.0.116.0) (default)
 2. Run backup image (version 7.0.98.0)
 3. Manually update images
 4. Change active boot image
 5. Clear Configuration

Please enter your choice: <input>5</input>

Detecting Hardware . . .



Re-building configuration filesystem
Done.



Bootloader 7.0.116.0 (Apr 13 2011 - 14:30:45)

Motorola PowerPC ProcessorID=00000000 Rev. PVR=80200020
        CPU: 833 MHz
        CCB: 333 MHz
        DDR: 166 MHz
        LBC: 41 MHz
L1 D-cache 32KB, L1 I-cache 32KB enabled.
I2C:   ready
DTT:   1 is 33 C
DRAM:  DDR module detected, total size:512MB.
512 MB
8540 in PCI Host Mode.
8540 is the PCI Arbiter.

Memory Test PASS

FLASH:
  Flash Bank 0: portsize = 2, size = 8 MB in 142 Sectors
 8 MB
L2 cache enabled: 256KB
Card Id: 1536
Card Revision Id: 1
Card CPU Id: 1287
Number of MAC Addresses: 32
Number of Slots Supported: 4
Serial Number: FOC1145F076
Unknown command Id: 0xa5
Unknown command Id: 0xa4
Unknown command Id: 0xa3
Manufacturers ID: 30464
Board Maintenance Level: 00
Number of supported APs: 100
In:    serial
Out:   serial
Err:   serial





                      .o88b. d888888b .d8888.  .o88b.  .d88b.
                     d8P  Y8   `88'   88'  YP d8P  Y8 .8P  Y8.
                     8P         88    `8bo.   8P      88    88
                     8b         88      `Y8b. 8b      88    88
                     Y8b  d8   .88.   db   8D Y8b  d8 `8b  d8'
                      `Y88P' Y888888P `8888Y'  `Y88P'  `Y88P'
                    Model AIR-WLC4404-100-K9   S/N: FOC1145F076
Net:
 PHY DEVICE  : Found Intel LXT971A PHY at 0x01
FEC ETHERNET
IDE:   Bus 0: OK
  Device 0: Model: SMART CF Firm: 20060811 Ser#: 00001011710100540124
            Type: Hard Disk
            Capacity: 247.0 MB = 0.2 GB (506016 x 512)
  Device 1: not available

Booting Primary Image...
Press <ESC> now for additional boot options...
Detecting Hardware . . .


Generating Secure Shell DSA Host Key ...
Generating Secure Shell RSA Host Key ...
Generating Secure Shell version 1.5 RSA Host Key ...

Cryptographic library self-test....passed!
XML config selected
Validating XML configuration
Cisco is a trademark of Cisco Systems, Inc.
Software Copyright Cisco Systems, Inc. All rights reserved.

Cisco AireOS Version 7.0.116.0
Initializing OS Services: ok
Initializing Serial Services: ok
Initializing Internal Interfaces: ok
Initializing Network Services: ok
Starting ARP Services: ok
Starting Trap Manager: ok
Starting Network Interface Management Services: ok
Starting System Services: ok
Starting FIPS Features: ok : Not enabled
Starting Fastpath Hardware Acceleration: ok
Starting Switching Services: ok
Starting QoS Services: ok
Starting Policy Manager: ok
Starting Data Transport Link Layer: ok
Starting Access Control List Services: ok
Starting System Interfaces: ok
Starting Client Troubleshooting Service: ok
Starting Management Frame Protection: ok
Starting Certificate Database: ok
Starting VPN Services: ok
Starting LWAPP: ok
Starting CAPWAP: ok
Starting LOCP: ok
Starting Security Services: ok
Starting Policy Manager: ok
Starting Authentication Engine: ok
Starting Mobility Management: ok
Starting Virtual AP Services: ok
Starting AireWave Director: ok
Starting Network Time Services: ok
Starting Cisco Discovery Protocol: ok
Starting Broadcast Services: ok
Starting Logging Services: ok
Starting DHCP Server: ok
Starting IDS Signature Manager: ok
Starting RFID Tag Tracking: ok
Starting Power Supply and Fan Status Monitoring Service: ok
Starting Mesh Services:  ok
Starting TSM: ok
Starting CIDS Services: ok
Starting Ethernet-over-IP: ok
Starting DTLS server:  enabled in CAPWAP
Starting CleanAir: ok
Starting WIPS: ok
Starting SSHPM LSC PROV LIST: ok
Starting RRC Services: ok
Starting FMC HS: ok
Starting Management Services:
   Web Server: ok
   CLI: ok
   Secure Web: Web Authentication Certificate not found (error). If you cannot access management interface via HTTPS please reconfigure Virtual Interface.

(Cisco Controller)


Welcome to the Cisco Wizard Configuration Tool
Use the '-' character to backup


Would you like to terminate autoinstall? [yes]:

System Name [Cisco_e9:4a:e3] (31 characters max):
AUTO-INSTALL: process terminated -- no configuration loaded
Cisco_4404
Enter Administrative User Name (24 characters max): <input>admin</input>
Enter Administrative Password (3 to 24 characters): <input>*****</input>
<notice>Default values (admin or Cisco or its variants) in password is not allowed.</notice>
Enter Administrative Password (3 to 24 characters): <input>*******</input>
<notice>Use at least three of the following four classes in the password: lowercase letters, uppercase letters, digits or special characters .</notice>
Enter Administrative Password (3 to 24 characters): <input>*******(L8heise)</input>
Re-enter Administrative Password                 : <input>*******</input>

Service Interface IP Address Configuration [static][DHCP]: <input>static</input>
Service Interface IP Address: <input>192.168.139.20</input>
Service Interface Netmask: <input>255.255.255.0</input>

Enable Link Aggregation (LAG) [yes][NO]: <input>NO</input>

Management Interface IP Address: <input>192.168.139.20</input>

<notice>Err: 192.168.139.20 cannot be on service port net (192.168.139.20/255.255.255.0)</notice>

Management Interface IP Address:
Invalid response


Management Interface IP Address: <input>192.168.146.20</input>
Management Interface Netmask: <input>255.255.255.0</input>
Management Interface Default Router: <input>192.168.146.1</input>
Management Interface VLAN Identifier (0 = untagged):
Management Interface Port Num [1 to 4]: <input>1</input>
Management Interface DHCP Server IP Address:
Invalid response

Management Interface DHCP Server IP Address: <input>172.16.4.77</input>
AP Manager Interface IP Address: <input>1.1.1.1</input>
AP Manager Interface Netmask: <input>255.255.255.0</input>
AP Manager Interface Default Router: <input>1.1.1.2</input>
AP Manager Interface VLAN Identifier (0 = untagged):
AP Manager Interface Port Num [1 to 4]: <input>2</input>
AP Manager Interface DHCP Server (172.16.4.77):

Virtual Gateway IP Address: <input>2.2.2.2</input>

Mobility/RF Group Name: <input>demo</input>

Network Name (SSID): <input>RE_Wireless</input>

Configure DHCP Bridging Mode [yes][NO]:

Allow Static IP Addresses [YES][no]:

Configure a RADIUS Server now? [YES][no]: <input>no</input>
Warning! The default WLAN security policy requires a RADIUS server.
Please see documentation for more details.

Enter Country Code list (enter 'help' for a list of countries) [US]: <input>help</input>
Enter the country code list (e.g. US,CA,MX) max=20.
Supported Country Codes:
AE, AR, AT, AU, BA, BE, BG, BH, BO, BR, BY, CA, CA2,
CH, CL, CM, CN, CO, CR, CY, CZ, DE, DK, DO, DZ, EC,
EE, EG, ES, FI, FR, GB, GI, GR, HK, HR, HU, ID, IE,
IL, ILO, IN, IQ, IS, IT, J2, J3, J4, JO, JP, KE, KR,
KW, KZ, LB, LI, LK, LT, LU, LV, MO, MC, ME, MK, MT,
MX, MY, NL, NO, NZ, OM, PA, PE, PH, PH2, PK, PL, PR,
PT, PY, QA, RO, RS, RU, SA, SE, SG, SI, SK, TH, TN,
TR, TW, UA, US, US2, USL, USX, UY, VE, VN, ZA

Enter Country Code list (enter 'help' for a list of countries) [US]: <input>DK</input>

Enable 802.11b Network [YES][no]: <input>no</input>
Enable 802.11a Network [YES][no]:
Enable Auto-RF [YES][no]:

Configure a NTP server now? [YES][no]: <input>no</input>
Configure the system time now? [YES][no]:
Enter the date in MM/DD/YY format: <input>041115</input>
Invalid response

Enter the date in MM/DD/YY format: <input>04/11/15</input>
Enter the time in HH:MM:SS format: <input>11:32:00</input>

Configuration correct? If yes, system will save it and reset. [yes][NO]: <input>yes</input>

Configuration saved!
Resetting system with new configuration...


Configuration saved!
Resetting system with new configuration...


Bootloader 7.0.116.0 (Apr 13 2011 - 14:30:45)

Motorola PowerPC ProcessorID=00000000 Rev. PVR=80200020
        CPU: 833 MHz
        CCB: 333 MHz
        DDR: 166 MHz
        LBC: 41 MHz
L1 D-cache 32KB, L1 I-cache 32KB enabled.
I2C:   ready
DTT:   1 is 35 C
DRAM:  DDR module detected, total size:512MB.
512 MB
8540 in PCI Host Mode.
8540 is the PCI Arbiter.

Memory Test PASS

FLASH:
  Flash Bank 0: portsize = 2, size = 8 MB in 142 Sectors
 8 MB
L2 cache enabled: 256KB
Card Id: 1536
Card Revision Id: 1
Card CPU Id: 1287
Number of MAC Addresses: 32
Number of Slots Supported: 4
Serial Number: FOC1145F076
Unknown command Id: 0xa5
Unknown command Id: 0xa4
Unknown command Id: 0xa3
Manufacturers ID: 30464
Board Maintenance Level: 00
Number of supported APs: 100
In:    serial
Out:   serial
Err:   serial





                      .o88b. d888888b .d8888.  .o88b.  .d88b.
                     d8P  Y8   `88'   88'  YP d8P  Y8 .8P  Y8.
                     8P         88    `8bo.   8P      88    88
                     8b         88      `Y8b. 8b      88    88
                     Y8b  d8   .88.   db   8D Y8b  d8 `8b  d8'
                      `Y88P' Y888888P `8888Y'  `Y88P'  `Y88P'
                    Model AIR-WLC4404-100-K9   S/N: FOC1145F076
Net:
 PHY DEVICE  : Found Intel LXT971A PHY at 0x01
FEC ETHERNET
IDE:   Bus 0: OK
  Device 0: Model: SMART CF Firm: 20060811 Ser#: 00001011710100540124
            Type: Hard Disk
            Capacity: 247.0 MB = 0.2 GB (506016 x 512)
  Device 1: not available

Booting Primary Image...
Press <ESC> now for additional boot options...
Detecting Hardware . . .



Cryptographic library self-test....passed!
XML config selected
Validating XML configuration
Cisco is a trademark of Cisco Systems, Inc.
Software Copyright Cisco Systems, Inc. All rights reserved.

Cisco AireOS Version 7.0.116.0
Initializing OS Services: ok
Initializing Serial Services: ok
Initializing Internal Interfaces: ok
Initializing Network Services: ok
Starting ARP Services: ok
Starting Trap Manager: ok
Starting Network Interface Management Services: ok
Starting System Services: ok
Starting FIPS Features: ok : Not enabled
Starting Fastpath Hardware Acceleration: ok
Starting Switching Services: ok
Starting QoS Services: ok
Starting Policy Manager: ok
Starting Data Transport Link Layer: ok
Starting Access Control List Services: ok
Starting System Interfaces: ok
Starting Client Troubleshooting Service: ok
Starting Management Frame Protection: ok
Starting Certificate Database: ok
Starting VPN Services: ok
Starting LWAPP: ok
Starting CAPWAP: ok
Starting LOCP: ok
Starting Security Services: ok
Starting Policy Manager: ok
Starting Authentication Engine: ok
Starting Mobility Management: ok
Starting Virtual AP Services: ok
Starting AireWave Director: ok
Starting Network Time Services: ok
Starting Cisco Discovery Protocol: ok
Starting Broadcast Services: ok
Starting Logging Services: ok
Starting DHCP Server: ok
Starting IDS Signature Manager: ok
Starting RFID Tag Tracking: ok
Starting Power Supply and Fan Status Monitoring Service: ok
Starting Mesh Services:  ok
Starting TSM: ok
Starting CIDS Services: ok
Starting Ethernet-over-IP: ok
Starting DTLS server:  enabled in CAPWAP
Starting CleanAir: ok
Starting WIPS: ok
Starting SSHPM LSC PROV LIST: ok
Starting RRC Services: ok
Starting FMC HS: ok
Starting Management Services:
   Web Server: ok
   CLI: ok
   Secure Web: ok

(Cisco Controller)

Enter User Name (or 'Recover-Config' this one-time only to reset configuration to factory defaults)