Difference between revisions of "QinQ Cisco IOS"
From Teknologisk videncenter
m (→QinQ) |
m (→QinQ) |
||
(8 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
=QinQ= | =QinQ= | ||
− | For at aktivere VLAN tagging skriver man i global configuration<ref>https://supportforums.cisco.com/thread/24704/ref> | + | For at aktivere VLAN tagging på nativ vlan<ref>https://supportforums.cisco.com/thread/160686</ref>, skriver man i global configuration<ref>https://supportforums.cisco.com/thread/24704/</ref> |
<pre> | <pre> | ||
− | vlan dot1q tag native | + | Switch#show vlan dot1q tag native |
+ | dot1q native vlan tagging is disabled | ||
+ | Switch#configure terminal | ||
+ | Switch(config)#vlan dot1q tag native | ||
</pre> | </pre> | ||
På interfacet definerer vi at alt trafik skal i vlan 130, men at den indre tag skal bibeholdes, og der skal klistres en ny på. | På interfacet definerer vi at alt trafik skal i vlan 130, men at den indre tag skal bibeholdes, og der skal klistres en ny på. | ||
Line 10: | Line 13: | ||
switchport mode dot1q-tunnel | switchport mode dot1q-tunnel | ||
</pre> | </pre> | ||
+ | ==Begrænsninger== | ||
+ | Configuring a port as an IEEE 802.1Q tunnel port has these limitations: | ||
+ | |||
+ | *IP routing and fallback bridging are not supported on tunnel ports. | ||
+ | *Tunnel ports do not support IP ACLs. | ||
+ | *If an IP ACL is applied to a trunk port in a VLAN that includes tunnel ports, or if a VLAN map is applied to a VLAN that includes tunnel ports, packets received from the tunnel port are treated as non-IP packets and are filtered with MAC access lists. | ||
+ | *Layer 3 quality of service (QoS) ACLs and other QoS features related to Layer 3 information are not supported on tunnel ports. | ||
+ | |||
+ | For more information about configuring IEEE 802.1Q tunnel ports, see the software configuration guide for this release. | ||
+ | |||
+ | ==Hardware understøttelse== | ||
+ | Hardware det virker på. | ||
+ | *ME-3400G-2CS-A (12.2(58)SE2 ME340x-METROIPACCESSK9-M) | ||
+ | *3550 | ||
+ | *6500 | ||
+ | *7600 | ||
+ | *Nexus 7000 | ||
+ | *Nexus 5000 |
Latest revision as of 16:45, 12 January 2012
QinQ
For at aktivere VLAN tagging på nativ vlan[1], skriver man i global configuration[2]
Switch#show vlan dot1q tag native dot1q native vlan tagging is disabled Switch#configure terminal Switch(config)#vlan dot1q tag native
På interfacet definerer vi at alt trafik skal i vlan 130, men at den indre tag skal bibeholdes, og der skal klistres en ny på.
interface FastEthernet 0/0 switchport access vlan 103 switchport mode dot1q-tunnel
Begrænsninger
Configuring a port as an IEEE 802.1Q tunnel port has these limitations:
- IP routing and fallback bridging are not supported on tunnel ports.
- Tunnel ports do not support IP ACLs.
- If an IP ACL is applied to a trunk port in a VLAN that includes tunnel ports, or if a VLAN map is applied to a VLAN that includes tunnel ports, packets received from the tunnel port are treated as non-IP packets and are filtered with MAC access lists.
- Layer 3 quality of service (QoS) ACLs and other QoS features related to Layer 3 information are not supported on tunnel ports.
For more information about configuring IEEE 802.1Q tunnel ports, see the software configuration guide for this release.
Hardware understøttelse
Hardware det virker på.
- ME-3400G-2CS-A (12.2(58)SE2 ME340x-METROIPACCESSK9-M)
- 3550
- 6500
- 7600
- Nexus 7000
- Nexus 5000