Difference between revisions of "Netband Project - Multicast"
From Teknologisk videncenter
(→Configuration) |
m (→Verification) |
||
| (8 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
| + | =Multicast= | ||
This page is part of the [[Netband_Project|Netband Project]] | This page is part of the [[Netband_Project|Netband Project]] | ||
*A multicast server is installed on the server HQDC1 | *A multicast server is installed on the server HQDC1 | ||
| Line 4: | Line 5: | ||
==Configuration== | ==Configuration== | ||
*Switch | *Switch | ||
| + | *Only configuration from HQSW1 is shown, as the configuration on B1SW1 is identical | ||
<pre>ip multicast-routing distributed | <pre>ip multicast-routing distributed | ||
! | ! | ||
| Line 10: | Line 12: | ||
no switchport | no switchport | ||
ip address 10.255.255.1 255.255.255.252 | ip address 10.255.255.1 255.255.255.252 | ||
| − | ip pim sparse-mode | + | ip pim sparse-dense-mode |
ip ospf network point-to-point | ip ospf network point-to-point | ||
ip ospf dead-interval minimal hello-multiplier 4 | ip ospf dead-interval minimal hello-multiplier 4 | ||
| Line 21: | Line 23: | ||
</pre> | </pre> | ||
*Routers | *Routers | ||
| + | *Only configuration from HQSRT1 is shown, as the configuration on B1RR1 is identical | ||
<pre>ip multicast-routing | <pre>ip multicast-routing | ||
! | ! | ||
| Line 43: | Line 46: | ||
! | ! | ||
</pre> | </pre> | ||
| + | [[Category:network]][[Category:CCNP]][[category:students]] | ||
==Verification== | ==Verification== | ||
<pre>B1sw1#sh ip mroute | <pre>B1sw1#sh ip mroute | ||
| + | ... | ||
(10.1.1.11, 239.0.0.40), 00:11:05/00:02:54, flags: JT | (10.1.1.11, 239.0.0.40), 00:11:05/00:02:54, flags: JT | ||
Incoming interface: FastEthernet0/2, RPF nbr 10.255.255.14 | Incoming interface: FastEthernet0/2, RPF nbr 10.255.255.14 | ||
| Line 51: | Line 56: | ||
Vlan5, Forward/Sparse, 00:11:05/00:02:48 | Vlan5, Forward/Sparse, 00:11:05/00:02:48 | ||
</pre> | </pre> | ||
| + | *Vlc is used as a the stream client | ||
| + | <br/> | ||
| + | |||
| + | [[Image:netband-vlc1.JPG|thumb|none|400px|Åben the multicast stream]] | ||
| + | [[Image:netband-vlc2.JPG|thumb|none|400px|Streaming]] | ||
| + | |||
| + | <br/> | ||
| + | ==Link== | ||
| + | Use iPerf as the multicast sender and listener | ||
| + | *https://gist.github.com/jayjanssen/5697813 | ||
Latest revision as of 21:14, 4 November 2014
Multicast
This page is part of the Netband Project
- A multicast server is installed on the server HQDC1
Configuration
- Switch
- Only configuration from HQSW1 is shown, as the configuration on B1SW1 is identical
ip multicast-routing distributed ! interface FastEthernet0/24 description HQrt1 no switchport ip address 10.255.255.1 255.255.255.252 ip pim sparse-dense-mode ip ospf network point-to-point ip ospf dead-interval minimal hello-multiplier 4 ! interface Vlan3 ip address 10.1.1.1 255.255.255.0 ip pim sparse-dense-mode ! ip pim rp-address 10.0.0.12
- Routers
- Only configuration from HQSRT1 is shown, as the configuration on B1RR1 is identical
ip multicast-routing ! interface Tunnel0 ip address 10.255.254.1 255.255.255.252 ip mtu 1300 ip pim sparse-dense-mode ip virtual-reassembly tunnel source Loopback1 tunnel destination 10.255.253.2 ! interface FastEthernet0/1 description HQSW1 ip address 10.255.255.2 255.255.255.252 ip pim sparse-dense-mode ip nat inside ip virtual-reassembly ip ospf network point-to-point ip ospf dead-interval minimal hello-multiplier 4 duplex auto speed auto !
Verification
B1sw1#sh ip mroute
...
(10.1.1.11, 239.0.0.40), 00:11:05/00:02:54, flags: JT
Incoming interface: FastEthernet0/2, RPF nbr 10.255.255.14
Outgoing interface list:
Vlan5, Forward/Sparse, 00:11:05/00:02:48
- Vlc is used as a the stream client
Link
Use iPerf as the multicast sender and listener