Difference between revisions of "Developing an optimum Design for Layer 3"
m (→Incremental SPF) |
m (→Bidirectional forward detection) |
||
| Line 71: | Line 71: | ||
|} | |} | ||
==Bidirectional forward detection== | ==Bidirectional forward detection== | ||
| + | BFD hjælper med at gøre route failover hurtigere ved at bruge en hurtigere lag 2 hello protokol end almindelige keep-alives. BFD skal også være understøttet af routing protokollen og har support i ospf, eigrp, isis og bgp. BFD kan tune rspons tiden ned til 50ms, hvad man er vant til fra SONET, men bruger ca 2 procent mere CPU. | ||
=Designing Scalable BGP Designs= | =Designing Scalable BGP Designs= | ||
Revision as of 19:51, 6 September 2011
Kapitel 3 fra CCDP ARCH bogen.
This article is under development....Contents
At designe avancerede IP adresserings løsninger
Design en ip adresseplan.
NAT
Nat mellem private adresser anbefales ikke
Nat gør netværksfejlfinding mindre overskueligt.
Nat til eksterne partnere.
Content Load-Balancing Device
En enhed der fordeler belastningen mellem flere Servere. For eksempel en enhed der fordeler forespørgsler fra WEB-brugere mellem ti identiske WEB-servere. Det kan være baseret på forskellige faktorer
- Antallet af forbindelser til hver server
- CPU belastning på Serverne
- En kombination af flere faktorer der beskriver servernes belastning
For eksempel Cisco CSS 11500 Series Content Services Switch
Designing avanceret Routning
Inappropriate Transit Traffic
Defensive filtering
Route redistribution
Migrating Between Routing Protocols
Two companies have been merged. Company A are running EIGRP and Company B are running OSPF.
Step 1: Redistribute between A & B
Step 2: Enable OSPF in company A, and make sure it has the highest Administrativ Distance
Step 3: When OSPF is running and is fully converged, Remove EIGRP
Route Summarization og Default Routing
Designing Scalable OSPF Design
OSPF Scalability best practise
- Any one Router should have no more than 60 adjacent neighbors
- An area should have no more than 50 Routers
- Any one Router should not be in mothe than three areas
- Already heavily loaded Routers should not be DR and BDR
Designing Areas
Network topology and addressing should be designed initially with division of areas in mind.
General advice about OSPF design is:
- Minimize the routing information advertised into and out of the area.
- Experience shows that you should be conservative about adding routers to the backbone area.
- Make it simple
- Make nonbackbone areas stub or totally stubby areas
- Make it summarized
Yada yada OMG OSPF
If hello timers are set to 1/3 second for 300 interfaces, each with 10 neighbors, the router would have to generate 900 hellos per second.
When the 3000 neighbors send 3 hellos per second back to the router, it has to process a
total of 9900 hellos per second.
Det er jo ikke realistisk, Cisco tag dig sammen
Incremental SPF
iSPF calculate only the part of the path tree that has changed.
The iSPF feature has been available since Cisco IOS Software Release 12.0(24)S, 12.3(2)T, 12.2(18)S, and 12.2(27)SBC. It is enabled with the iSPF router command under an OSPF process.
Bidirectional forward detection
BFD hjælper med at gøre route failover hurtigere ved at bruge en hurtigere lag 2 hello protokol end almindelige keep-alives. BFD skal også være understøttet af routing protokollen og har support i ospf, eigrp, isis og bgp. BFD kan tune rspons tiden ned til 50ms, hvad man er vant til fra SONET, men bruger ca 2 procent mere CPU.
Designing Scalable BGP Designs
Vis BGP slide...
