Difference between revisions of "Wired to Wireless bridge single SSID"
m |
m |
||
| Line 1: | Line 1: | ||
| + | =Basic interface configuration= | ||
| + | Configure VLAN 1 with an IP address and associate wlan-ap0 with it. | ||
<source lang=cli> | <source lang=cli> | ||
Router#<input>conf t</input> | Router#<input>conf t</input> | ||
Enter configuration commands, one per line. End with CNTL/Z. | Enter configuration commands, one per line. End with CNTL/Z. | ||
Router(config)#<input>int vlan 1</input> | Router(config)#<input>int vlan 1</input> | ||
| − | Router(config-if)#<input>ip address 192.168.64.4 255.255.255.0<input> | + | Router(config-if)#<input>ip address 192.168.64.4 255.255.255.0</input> |
| − | Router(config-if)#<input>interface wlan-ap0<input> | + | Router(config-if)#<input>interface wlan-ap0</input> |
The wlan-ap 0 interface is used for managing the embedded AP. | The wlan-ap 0 interface is used for managing the embedded AP. | ||
Please use the "service-module wlan-ap 0 session" command to console into the embedded AP | Please use the "service-module wlan-ap 0 session" command to console into the embedded AP | ||
| − | Router(config-if)#<input>ip unnumbered vlan 1<input> | + | Router(config-if)#<input>ip unnumbered vlan 1</input> |
| − | Router(config-if)#<input>no shutdown<input> | + | Router(config-if)#<input>no shutdown</input> |
| − | + | </source> | |
| − | + | ==Check interface status== | |
| − | + | Router#<input>show ip interface brief</input> | |
| − | Router#<input>show ip interface brief<input> | ||
Interface IP-Address OK? Method Status Protocol | Interface IP-Address OK? Method Status Protocol | ||
ATM0 unassigned YES unset administratively down down | ATM0 unassigned YES unset administratively down down | ||
| Line 26: | Line 27: | ||
GigabitEthernet7 unassigned YES unset down down | GigabitEthernet7 unassigned YES unset down down | ||
GigabitEthernet8 unassigned YES unset administratively down down | GigabitEthernet8 unassigned YES unset administratively down down | ||
| − | Vlan1 192.168.64.4 YES manual up up | + | Vlan1 <notice>192.168.64.4</notice> YES manual up up |
Wlan-GigabitEthernet8 unassigned YES unset up up | Wlan-GigabitEthernet8 unassigned YES unset up up | ||
| − | wlan-ap0 192.168.64.4 YES TFTP up up | + | wlan-ap0 <notice>192.168.64.4</notice> YES TFTP up up |
</source> | </source> | ||
| − | + | =Setup the access point part 1= | |
| + | The access point - AP -'''wlan-ap0''' is a built in service module running its own IOS. To connect to the AP use the '''service-module''' command from the Routers IOS. | ||
| + | =Connecting | ||
{{Source cli}} | {{Source cli}} | ||
Revision as of 10:05, 15 June 2014
Basic interface configuration
Configure VLAN 1 with an IP address and associate wlan-ap0 with it.
Router#<input>conf t</input>
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#<input>int vlan 1</input>
Router(config-if)#<input>ip address 192.168.64.4 255.255.255.0</input>
Router(config-if)#<input>interface wlan-ap0</input>
The wlan-ap 0 interface is used for managing the embedded AP.
Please use the "service-module wlan-ap 0 session" command to console into the embedded AP
Router(config-if)#<input>ip unnumbered vlan 1</input>
Router(config-if)#<input>no shutdown</input>Check interface status
Router#<input>show ip interface brief</input> Interface IP-Address OK? Method Status Protocol ATM0 unassigned YES unset administratively down down Ethernet0 unassigned YES unset administratively down down GigabitEthernet0 unassigned YES unset up up GigabitEthernet1 unassigned YES unset down down GigabitEthernet2 unassigned YES unset down down GigabitEthernet3 unassigned YES unset down down GigabitEthernet4 unassigned YES unset down down GigabitEthernet5 unassigned YES unset down down GigabitEthernet6 unassigned YES unset down down GigabitEthernet7 unassigned YES unset down down GigabitEthernet8 unassigned YES unset administratively down down Vlan1 <notice>192.168.64.4</notice> YES manual up up Wlan-GigabitEthernet8 unassigned YES unset up up wlan-ap0 <notice>192.168.64.4</notice> YES TFTP up up </source>
Setup the access point part 1
The access point - AP -wlan-ap0 is a built in service module running its own IOS. To connect to the AP use the service-module command from the Routers IOS. =Connecting