Difference between revisions of "Basic configuration IPv6 Cisco IOS"
From Teknologisk videncenter
m (→Default IPv6 Unicast Route) |
m (Fjernet IPv6 enable, da den kun skal bruges hvis man ikke sætter en IPv6 addresse på interfacet. Men vil have IPv6 enabled.) |
||
| (One intermediate revision by one other user not shown) | |||
| Line 9: | Line 9: | ||
<source lang=cli> | <source lang=cli> | ||
R3(config)#<input>int fa0/0</input> | R3(config)#<input>int fa0/0</input> | ||
| − | |||
R3(config-if)#<input>ipv6 address 2001:16D8:DD85:139::7/64</input> | R3(config-if)#<input>ipv6 address 2001:16D8:DD85:139::7/64</input> | ||
R3(config-if)#<input>exit</input> | R3(config-if)#<input>exit</input> | ||
R3(config)#<input>int fa0/1</input> | R3(config)#<input>int fa0/1</input> | ||
| − | |||
R3(config-if)#<input>ipv6 address 2001:16D8:DD85:140::1/64</input> | R3(config-if)#<input>ipv6 address 2001:16D8:DD85:140::1/64</input> | ||
R3(config-if)#<input>ipv6 dhcp relay destination 2001:16D8:DD85:4::166</input> | R3(config-if)#<input>ipv6 dhcp relay destination 2001:16D8:DD85:4::166</input> | ||
| Line 61: | Line 59: | ||
ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 | ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 | ||
S 2000::/3 [1/0] | S 2000::/3 [1/0] | ||
| − | via | + | via fastethernet0/0 fe80::221:6bff:fe52:e36 |
C 2001:16D8:DD85:139::/64 [0/0] | C 2001:16D8:DD85:139::/64 [0/0] | ||
via FastEthernet0/0, directly connected | via FastEthernet0/0, directly connected | ||
| Line 73: | Line 71: | ||
via Null0, receive | via Null0, receive | ||
</source> | </source> | ||
| + | |||
==Pinging== | ==Pinging== | ||
<source lang=cli> | <source lang=cli> | ||
Latest revision as of 10:58, 31 October 2013
Contents
Enabling IPv6 Globally
Start the IPv6 routing process and allow IPv6 CEF switching.
R3(config)#<input>ipv6 unicast-routing</input>
R3(config)#<input>ipv6 cef</input>Configuring IPv6 address on interface
R3(config)#<input>int fa0/0</input>
R3(config-if)#<input>ipv6 address 2001:16D8:DD85:139::7/64</input>
R3(config-if)#<input>exit</input>
R3(config)#<input>int fa0/1</input>
R3(config-if)#<input>ipv6 address 2001:16D8:DD85:140::1/64</input>
R3(config-if)#<input>ipv6 dhcp relay destination 2001:16D8:DD85:4::166</input>Showing IPv6 configuration on interface
R3#<input>show ipv6 int fa0/0</input>
FastEthernet0/0 is up, line protocol is up
IPv6 is enabled, link-local address is FE80::128C:CFFF:FE2E:916E
No Virtual link-local address(es):
Global unicast address(es):
2001:16D8:DD85:139::7, subnet is 2001:16D8:DD85:139::/64
Joined group address(es):
FF02::1
FF02::2
FF02::1:FF00:7
FF02::1:FF2E:916E
MTU is 1500 bytes
ICMP error messages limited to one every 100 milliseconds
ICMP redirects are enabled
ICMP unreachables are sent
ND DAD is enabled, number of DAD attempts: 1
ND reachable time is 30000 milliseconds (using 30000)
ND advertised reachable time is 0 (unspecified)
ND advertised retransmit interval is 0 (unspecified)
ND router advertisements are sent every 200 seconds
ND router advertisements live for 1800 seconds
ND advertised default router preference is Medium
Hosts use stateless autoconfig for addresses.Default IPv6 Unicast Route
Notice the 2000::/3 prefix which identifies the total IPv6 Unicast area. It is recomended to use link local address as next-hop address. If using the Global Unicast address Router redirection will not work.
R3(config)#<input>ipv6 route 2000::/3 fastethernet0/0 fe80::221:6bff:fe52:e36</input>Showing IPv6 Route table
R3#<input>show ipv6 route</input>
IPv6 Routing Table - default - 7 entries
Codes: C - Connected, L - Local, S - Static, U - Per-user Static route
B - BGP, HA - Home Agent, MR - Mobile Router, R - RIP
I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary
D - EIGRP, EX - EIGRP external, NM - NEMO, ND - Neighbor Discovery
l - LISP
O - OSPF Intra, OI - OSPF Inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
S 2000::/3 [1/0]
via fastethernet0/0 fe80::221:6bff:fe52:e36
C 2001:16D8:DD85:139::/64 [0/0]
via FastEthernet0/0, directly connected
L 2001:16D8:DD85:139::7/128 [0/0]
via FastEthernet0/0, receive
C 2001:16D8:DD85:140::/64 [0/0]
via FastEthernet0/1, directly connected
L 2001:16D8:DD85:140::1/128 [0/0]
via FastEthernet0/1, receive
L FF00::/8 [0/0]
via Null0, receivePinging
ping 2001:200:dff:fff1:216:3eff:feb1:44d7or
R1#<input>ping www.v6.facebook.com</input>
Translating "www.v6.facebook.com"...domain server (172.16.4.66) [OK]
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2620:0:1CFE:<notice>FACE:B00C</notice>::3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 164/168/176 msRIP
ipv6 router rip RIPNGR3
!
int fastethernet0/1
ipv6 address 2001:410:ffff:1::1/64
ipv6 rip RIPNGR3 enable
ipv6 rip default-information originate
!
int fastethernet0/0
ipv6 address 2001:410:ffff:2::1/64
ipv6 rip RIPNGR3 enable
ipv6 rip default-information originate
!
ipv6 route ::/0 ethernet0