|
|
(5 intermediate revisions by the same user not shown) |
Line 1: |
Line 1: |
− | = Purpose of GLBP =
| + | #Redirect [[GLBP]] |
− | | |
− | :The purpose of GLBP is to ensure network connectivity in case of Router or access circuit failure. GLBP automatically Load balances the load from the IP traffic sources.
| |
− | | |
− | :Gateway Load Balancing Protocol (GLBP) is a Cisco proprietary protocol that attempts to overcome the limitations of existing redundant router protocols by adding basic load balancing functionality.
| |
− | | |
− | = Other high availability protocols =
| |
− | *HSRP [[Hot Standby Router Protocol]]
| |
− | *VRRP [[Virtual Router Redundancy Protocol]]
| |
− | | |
− | = GLBP functions =
| |
− | *Active virtual gateway (AVG): Members of a GLBP group elect one gateway to be the AVG for that group. Other group members provide backup for the AVG if the AVG becomes unavailable. The AVG assigns a virtual MAC address to each member of the group.
| |
− | *Active virtual forwarder (AVF): Each gateway assumes responsibility for forwarding packets sent to the virtual MAC address assigned to it by the AVG. These gateways are known as AVFs for their virtual MAC address.
| |
− | *Communication: GLBP members communicate with each other using hello messages sent every 3 seconds to the multicast address 224.0.0.102, User Datagram Protocol (UDP) port 3222.
| |
− | | |
− | = GLBP features =
| |
− | *Load sharing: Traffic from LAN clients can be shared by multiple routers.
| |
− | *Multiple virtual routers: Up to 1,024 virtual routers (GLBP groups) can be on each physical interface of a router, and there can be up to four virtual forwarders per group.
| |
− | *Preemption: You can preempt an AVG with a higher priority backup virtual gateway. Forwarder preemption works in a similar way, except that it uses weighting instead of priority and is enabled by default.
| |
− | *Efficient resource utilization: Any router in a group can serve as a backup, which eliminates the need for a dedicated backup router because all available routers can support network traffic.
| |
− | = How does GLBP work =
| |
− | {|
| |
− | |
| |
− | [[Image:GLBP1.png|thumb|500px|float|Picture 1: GLBP group with Router R1 as AVG and AVF and Router R2 and R3 as AVF]]
| |
− | |valign="top"|
| |
− | == GLBP Roles ==
| |
− | === AVG - Active Virtual Gateway ===
| |
− | The Router with the highest priority is chosen as the AVG. The AVG has the responsebility of assigning MAC addresses to the AVF Routers.
| |
− | === AVF - Active Virtual Forwarder ===
| |
− | The AVF Routers Route traffic from the connected clients. Each AVF is assigned its own MAC-Address. The MAC-Address is assigned from the AVG.
| |
− | |}
| |
− |
| |
− | {|
| |
− | |
| |
− | <pre>
| |
− | hostname R1
| |
− | !
| |
− | interface FastEthernet1/0
| |
− | ip address 10.0.0.11 255.0.0.0
| |
− | standby 10 priority 130
| |
− | standby 10 preempt
| |
− | standby 10 timers 2 6
| |
− | standby 10 ip 10.0.0.1
| |
− | </pre>
| |
− | |
| |
− | <pre>
| |
− | hostname R2
| |
− | !
| |
− | interface FastEthernet1/0
| |
− | ip address 10.0.0.12 255.0.0.0
| |
− | standby 10 priority 120
| |
− | standby 10 preempt
| |
− | standby 10 timers 2 6
| |
− | standby 10 ip 10.0.0.1
| |
− | </pre>
| |
− | |
| |
− | <pre>
| |
− | hostname R3
| |
− | !
| |
− | interface FastEthernet1/0
| |
− | ip address 10.0.0.13 255.0.0.0
| |
− | standby 10 priority 110
| |
− | standby 10 preempt
| |
− | standby 10 timers 2 6
| |
− | standby 10 ip 10.0.0.1
| |
− | </pre>
| |
− | |}
| |
− | | |
− | [[Category:Cisco]][[Category:CCNP]][[Category:IOS]][[Category:Network]][[Category:CCNP3]]
| |