--- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: <input>yes</input>

R5>enable
Password:
R5#

R5#<input>erase startup-config</input>
Erasing the nvram filesystem will remove all configuration files! Continue? [confirm]
[OK]
Erase of nvram: complete
R5#<input>reload</input>

         --- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: <input>yes</input>

At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.

Basic management setup configures only enough connectivity
for management of the system, extended setup will ask you
to configure each interface on the system

Would you like to enter basic management setup? [yes/no]: <input>yes</input>
Configuring global parameters:

  Enter host name [Router]: <input>Viborg1</input>

  The enable secret is a password used to protect access to
  privileged EXEC and configuration modes. This password, after
  entered, becomes encrypted in the configuration.
  Enter enable secret: <input>cisco</input>

  The enable password is used when you do not specify an
  enable secret password, with some older software versions, and
  some boot images.
  Enter enable password: <input>class</input>

  The virtual terminal password is used to protect
  access to the router over a network interface.
  Enter virtual terminal password: <input>cisco</input>
  Configure SNMP Network Management? [yes]: <input>no</input>

Current interface summary


Any interface listed with OK? value "NO" does not have a valid configuration

Interface                  IP-Address      OK? Method Status                Protocol
FastEthernet0/0            unassigned      NO  unset  up                    down
FastEthernet0/1            unassigned      NO  unset  up                    down

Enter interface name used to connect to the
management network from the above interface summary: FastEthernet0/0

Configuring interface FastEthernet0/0:
  Use the 100 Base-TX (RJ-45) connector? [yes]:<input>yes</input>
  Operate in full-duplex mode? [no]: <input>yes</input>
  Configure IP on this interface? [yes]:<input>yes</input>
    IP address for this interface: <input>192.168.22.1</input>
    Subnet mask for this interface [255.255.255.0] :<input>255.255.255.0</input>
    Class C network is 192.168.22.0, 24 subnet bits; mask is /24

The following configuration command script was created:

hostname Viborg1
enable secret 5 $1$Q0eK$BS6PyvYOB0dfDILGrDYLc.
enable password class
line vty 0 4
password cisco
no snmp-server
!
no ip routing

!
interface FastEthernet0/0
no shutdown
media-type 100BaseX
full-duplex
ip address 192.168.22.1 255.255.255.0
no mop enabled
!
interface FastEthernet0/1
shutdown
no ip address
!
end


[0] Go to the IOS command prompt without saving this config.
[1] Return back to the setup without saving this config.
[2] Save this configuration to nvram and exit.

Enter your selection [2]:<input>2</input>

Viborg1><input>enable</input>
Viborg1#<input>configure terminal</input>
Enter configuration commands, one per line.  End with CNTL/Z.
Viborg1(config)#<input>interface FastEthernet0/1</input>
Viborg1(config-if)#<input>ip address 172.16.0.1 255.255.0.0</input>
Viborg1(config-if)#<input>no shutdown</input>
Viborg1(config-if)#<input>CTRL-Z</input>

Viborg1#<input>configure terminal</input>
Viborg1(config)#<input>interface loopback 0</input>
Viborg1(config-if)#<input>ip address 10.10.10.1 255.255.255.255</input>
Viborg1(config-if)#<input>no shutdown</input>
Viborg1(config-if)#<input>CTRL-Z</input>

Viborg1#<input>configure terminal</input>
Viborg1(config)#<input>ip routing</input>
Viborg1(config)#<input>router rip</input>
Viborg1(config-router)#<input>version 2</input>
Viborg1(config-router)#<input>network 192.168.22.0</input>
Viborg1(config-router)#<input>network 172.16.0.0</input>
Viborg1(config-router)#<input>network 10.0.0.0</input>
Viborg1(config-router)#<input>CTRL-Z</input>