Difference between revisions of "STM32F107VC/Interrupts and Events"
From Teknologisk videncenter
m (→Example using USART2 interrupt) |
m (→Example using USART2 interrupt) |
||
Line 14: | Line 14: | ||
:Priority: '''45''' - Settable | :Priority: '''45''' - Settable | ||
:Address: '''0x0000_00D8''' | :Address: '''0x0000_00D8''' | ||
+ | =Default Setup= | ||
+ | The default Keil uVision [[STM32F107VC]] startup file ''startup_stm32f10x_cl.s'' contains the startup code and the Interrupt entries. Partial config below. | ||
+ | <source lang=asm> | ||
+ | Stack_Size EQU 0x00000200 | ||
+ | AREA STACK, NOINIT, READWRITE, ALIGN=3 | ||
+ | Stack_Mem SPACE Stack_Size | ||
+ | __initial_sp | ||
+ | AREA RESET, DATA, READONLY | ||
+ | EXPORT __Vectors | ||
+ | EXPORT __Vectors_End | ||
+ | EXPORT __Vectors_Size | ||
+ | |||
+ | __Vectors DCD __initial_sp ; Top of Stack (Linker puts top-of-stack address in location 0x00000000) | ||
+ | DCD Reset_Handler ; Reset Handler (Vector address of Reset. The PC - Program Counter - loads this address on Reset | ||
+ | DCD NMI_Handler ; NMI Handler | ||
+ | DCD HardFault_Handler ; Hard Fault Handler | ||
+ | DCD MemManage_Handler ; MPU Fault Handler | ||
+ | DCD BusFault_Handler ; Bus Fault Handler | ||
+ | DCD UsageFault_Handler ; Usage Fault Handler | ||
+ | DCD 0 ; Reserved | ||
+ | DCD 0 ; Reserved | ||
+ | DCD 0 ; Reserved | ||
+ | DCD 0 ; Reserved | ||
+ | DCD SVC_Handler ; SVCall Handler | ||
+ | DCD DebugMon_Handler ; Debug Monitor Handler | ||
+ | DCD 0 ; Reserved | ||
+ | DCD PendSV_Handler ; PendSV Handler | ||
+ | DCD SysTick_Handler ; SysTick Handler | ||
+ | |||
+ | ; External Interrupts | ||
+ | DCD WWDG_IRQHandler ; 0: Window Watchdog | ||
+ | DCD PVD_IRQHandler ; 1: PVD through EXTI Line detect | ||
+ | DCD TAMPER_IRQHandler ; 2: Tamper | ||
+ | DCD RTC_IRQHandler ; 3: RTC | ||
+ | DCD FLASH_IRQHandler ; 4: Flash | ||
+ | DCD RCC_IRQHandler ; 5: RCC | ||
+ | DCD EXTI0_IRQHandler ; 6: EXTI Line 0 | ||
+ | DCD EXTI1_IRQHandler ; 7: EXTI Line 1 | ||
+ | DCD EXTI2_IRQHandler ; 8: EXTI Line 2 | ||
+ | DCD EXTI3_IRQHandler ; 9: EXTI Line 3 | ||
+ | DCD EXTI4_IRQHandler ; 10: EXTI Line 4 | ||
+ | DCD DMA1_Channel1_IRQHandler ; 11: DMA1 Channel 1 | ||
+ | DCD DMA1_Channel2_IRQHandler ; 12: DMA1 Channel 2 | ||
+ | DCD DMA1_Channel3_IRQHandler ; 13: DMA1 Channel 3 | ||
+ | DCD DMA1_Channel4_IRQHandler ; 14: DMA1 Channel 4 | ||
+ | DCD DMA1_Channel5_IRQHandler ; 15: DMA1 Channel 5 | ||
+ | DCD DMA1_Channel6_IRQHandler ; 16: DMA1 Channel 6 | ||
+ | DCD DMA1_Channel7_IRQHandler ; 17: DMA1 Channel 7 | ||
+ | DCD ADC1_2_IRQHandler ; 18: ADC1 and ADC2 | ||
+ | DCD CAN1_TX_IRQHandler ; 19: CAN1 TX | ||
+ | DCD CAN1_RX0_IRQHandler ; 20: CAN1 RX0 | ||
+ | DCD CAN1_RX1_IRQHandler ; 21: CAN1 RX1 | ||
+ | DCD CAN1_SCE_IRQHandler ; 22: CAN1 SCE | ||
+ | DCD EXTI9_5_IRQHandler ; 23: EXTI Line 9..5 | ||
+ | DCD TIM1_BRK_IRQHandler ; 24: TIM1 Break | ||
+ | DCD TIM1_UP_IRQHandler ; 25: TIM1 Update | ||
+ | DCD TIM1_TRG_COM_IRQHandler ; 26: TIM1 Trigger and Commutation | ||
+ | DCD TIM1_CC_IRQHandler ; 27: TIM1 Capture Compare | ||
+ | DCD TIM2_IRQHandler ; 28: TIM2 | ||
+ | DCD TIM3_IRQHandler ; 29: TIM3 | ||
+ | DCD TIM4_IRQHandler ; 30: TIM4 | ||
+ | DCD I2C1_EV_IRQHandler ; 31: I2C1 Event | ||
+ | DCD I2C1_ER_IRQHandler ; 32: I2C1 Error | ||
+ | DCD I2C2_EV_IRQHandler ; 33: I2C2 Event | ||
+ | DCD I2C2_ER_IRQHandler ; 34: I2C2 Error | ||
+ | DCD SPI1_IRQHandler ; 35: SPI1 | ||
+ | DCD SPI2_IRQHandler ; 36: SPI2 | ||
+ | DCD USART1_IRQHandler ; 37: USART1 | ||
+ | DCD USART2_IRQHandler ; 38: USART2 | ||
+ | DCD USART3_IRQHandler ; 39: USART3 | ||
+ | DCD EXTI15_10_IRQHandler ; 40: EXTI Line 15..10 | ||
+ | DCD RTCAlarm_IRQHandler ; 41: RTC Alarm through EXTI Line | ||
+ | DCD OTG_FS_WKUP_IRQHandler ; 42: USB OTG FS Wakeup | ||
+ | DCD Default_Handler ; 43: Reserved | ||
+ | DCD Default_Handler ; 44: Reserved | ||
+ | DCD Default_Handler ; 45: Reserved | ||
+ | DCD Default_Handler ; 46: Reserved | ||
+ | DCD Default_Handler ; 47: Reserved | ||
+ | DCD Default_Handler ; 48: Reserved | ||
+ | DCD Default_Handler ; 49: Reserved | ||
+ | DCD TIM5_IRQHandler ; 50: TIM5 | ||
+ | DCD SPI3_IRQHandler ; 51: SPI3 | ||
+ | DCD UART4_IRQHandler ; 52: UART4 | ||
+ | DCD UART5_IRQHandler ; 53: UART5 | ||
+ | DCD TIM6_IRQHandler ; 54: TIM6 | ||
+ | DCD TIM7_IRQHandler ; 55: TIM7 | ||
+ | DCD DMA2_Channel1_IRQHandler ; 56: DMA2 Channel 1 | ||
+ | DCD DMA2_Channel2_IRQHandler ; 57: DMA2 Channel 2 | ||
+ | DCD DMA2_Channel3_IRQHandler ; 58: DMA2 Channel 3 | ||
+ | DCD DMA2_Channel4_IRQHandler ; 59: DMA2 Channel 4 | ||
+ | DCD DMA2_Channel5_IRQHandler ; 60: DMA2 Channel 5 | ||
+ | DCD ETH_IRQHandler ; 61: Ethernet | ||
+ | DCD ETH_WKUP_IRQHandler ; 62: Ethernet Wakeup | ||
+ | DCD CAN2_TX_IRQHandler ; 63: CAN2 TX | ||
+ | DCD CAN2_RX0_IRQHandler ; 64: CAN2 RX0 | ||
+ | DCD CAN2_RX1_IRQHandler ; 65: CAN2 RX1 | ||
+ | DCD CAN2_SCE_IRQHandler ; 66: CAN2 SCE | ||
+ | DCD OTG_FS_IRQHandler ; 67: USB On-The-Go FS | ||
+ | __Vectors_End | ||
+ | |||
+ | __Vectors_Size EQU __Vectors_End - __Vectors | ||
+ | |||
+ | AREA |.text|, CODE, READONLY | ||
+ | |||
+ | |||
+ | ; Reset Handler | ||
+ | |||
+ | Reset_Handler PROC | ||
+ | EXPORT Reset_Handler [WEAK] | ||
+ | IMPORT __main | ||
+ | LDR R0, =__main ; Jump to main() | ||
+ | BX R0 | ||
+ | ENDP | ||
+ | |||
+ | |||
+ | ; Dummy Exception Handlers (infinite loops which can be modified) | ||
+ | |||
+ | NMI_Handler PROC | ||
+ | EXPORT NMI_Handler [WEAK] | ||
+ | B . ; B . means Branch to this address | ||
+ | ENDP | ||
+ | </source> | ||
[[Category:STM32F107VC]][[Category:ARM]] | [[Category:STM32F107VC]][[Category:ARM]] |
Revision as of 09:40, 12 September 2011
Contents
Nested vectored interrupt controller (NVIC)
- See the Reference manual Chapter 10. Remember the STM32F107VC is a connectivity line device.
- See the STM32F10xxx/20/21/L1 Cortex-M3 programming manual Section 4.3 for programming information. (See section 4.3.10 NVIC Design hints and Tips)
Features
- 68 (not including the sixteen Cortex™-M3 interrupt lines)
- 16 programmable priority levels (4 bits of interrupt priority are used)
- Low-latency exception and interrupt handling
- Power management control
- Implementation of System Control Registers
Example using USART2 interrupt
From the [Reference manual] table 61 in section 10.1.2 its seen that
- USART2 global interrupt
- Position: 28
- Priority: 45 - Settable
- Address: 0x0000_00D8
Default Setup
The default Keil uVision STM32F107VC startup file startup_stm32f10x_cl.s contains the startup code and the Interrupt entries. Partial config below.
Stack_Size EQU 0x00000200
AREA STACK, NOINIT, READWRITE, ALIGN=3
Stack_Mem SPACE Stack_Size
__initial_sp
AREA RESET, DATA, READONLY
EXPORT __Vectors
EXPORT __Vectors_End
EXPORT __Vectors_Size
__Vectors DCD __initial_sp ; Top of Stack (Linker puts top-of-stack address in location 0x00000000)
DCD Reset_Handler ; Reset Handler (Vector address of Reset. The PC - Program Counter - loads this address on Reset
DCD NMI_Handler ; NMI Handler
DCD HardFault_Handler ; Hard Fault Handler
DCD MemManage_Handler ; MPU Fault Handler
DCD BusFault_Handler ; Bus Fault Handler
DCD UsageFault_Handler ; Usage Fault Handler
DCD 0 ; Reserved
DCD 0 ; Reserved
DCD 0 ; Reserved
DCD 0 ; Reserved
DCD SVC_Handler ; SVCall Handler
DCD DebugMon_Handler ; Debug Monitor Handler
DCD 0 ; Reserved
DCD PendSV_Handler ; PendSV Handler
DCD SysTick_Handler ; SysTick Handler
; External Interrupts
DCD WWDG_IRQHandler ; 0: Window Watchdog
DCD PVD_IRQHandler ; 1: PVD through EXTI Line detect
DCD TAMPER_IRQHandler ; 2: Tamper
DCD RTC_IRQHandler ; 3: RTC
DCD FLASH_IRQHandler ; 4: Flash
DCD RCC_IRQHandler ; 5: RCC
DCD EXTI0_IRQHandler ; 6: EXTI Line 0
DCD EXTI1_IRQHandler ; 7: EXTI Line 1
DCD EXTI2_IRQHandler ; 8: EXTI Line 2
DCD EXTI3_IRQHandler ; 9: EXTI Line 3
DCD EXTI4_IRQHandler ; 10: EXTI Line 4
DCD DMA1_Channel1_IRQHandler ; 11: DMA1 Channel 1
DCD DMA1_Channel2_IRQHandler ; 12: DMA1 Channel 2
DCD DMA1_Channel3_IRQHandler ; 13: DMA1 Channel 3
DCD DMA1_Channel4_IRQHandler ; 14: DMA1 Channel 4
DCD DMA1_Channel5_IRQHandler ; 15: DMA1 Channel 5
DCD DMA1_Channel6_IRQHandler ; 16: DMA1 Channel 6
DCD DMA1_Channel7_IRQHandler ; 17: DMA1 Channel 7
DCD ADC1_2_IRQHandler ; 18: ADC1 and ADC2
DCD CAN1_TX_IRQHandler ; 19: CAN1 TX
DCD CAN1_RX0_IRQHandler ; 20: CAN1 RX0
DCD CAN1_RX1_IRQHandler ; 21: CAN1 RX1
DCD CAN1_SCE_IRQHandler ; 22: CAN1 SCE
DCD EXTI9_5_IRQHandler ; 23: EXTI Line 9..5
DCD TIM1_BRK_IRQHandler ; 24: TIM1 Break
DCD TIM1_UP_IRQHandler ; 25: TIM1 Update
DCD TIM1_TRG_COM_IRQHandler ; 26: TIM1 Trigger and Commutation
DCD TIM1_CC_IRQHandler ; 27: TIM1 Capture Compare
DCD TIM2_IRQHandler ; 28: TIM2
DCD TIM3_IRQHandler ; 29: TIM3
DCD TIM4_IRQHandler ; 30: TIM4
DCD I2C1_EV_IRQHandler ; 31: I2C1 Event
DCD I2C1_ER_IRQHandler ; 32: I2C1 Error
DCD I2C2_EV_IRQHandler ; 33: I2C2 Event
DCD I2C2_ER_IRQHandler ; 34: I2C2 Error
DCD SPI1_IRQHandler ; 35: SPI1
DCD SPI2_IRQHandler ; 36: SPI2
DCD USART1_IRQHandler ; 37: USART1
DCD USART2_IRQHandler ; 38: USART2
DCD USART3_IRQHandler ; 39: USART3
DCD EXTI15_10_IRQHandler ; 40: EXTI Line 15..10
DCD RTCAlarm_IRQHandler ; 41: RTC Alarm through EXTI Line
DCD OTG_FS_WKUP_IRQHandler ; 42: USB OTG FS Wakeup
DCD Default_Handler ; 43: Reserved
DCD Default_Handler ; 44: Reserved
DCD Default_Handler ; 45: Reserved
DCD Default_Handler ; 46: Reserved
DCD Default_Handler ; 47: Reserved
DCD Default_Handler ; 48: Reserved
DCD Default_Handler ; 49: Reserved
DCD TIM5_IRQHandler ; 50: TIM5
DCD SPI3_IRQHandler ; 51: SPI3
DCD UART4_IRQHandler ; 52: UART4
DCD UART5_IRQHandler ; 53: UART5
DCD TIM6_IRQHandler ; 54: TIM6
DCD TIM7_IRQHandler ; 55: TIM7
DCD DMA2_Channel1_IRQHandler ; 56: DMA2 Channel 1
DCD DMA2_Channel2_IRQHandler ; 57: DMA2 Channel 2
DCD DMA2_Channel3_IRQHandler ; 58: DMA2 Channel 3
DCD DMA2_Channel4_IRQHandler ; 59: DMA2 Channel 4
DCD DMA2_Channel5_IRQHandler ; 60: DMA2 Channel 5
DCD ETH_IRQHandler ; 61: Ethernet
DCD ETH_WKUP_IRQHandler ; 62: Ethernet Wakeup
DCD CAN2_TX_IRQHandler ; 63: CAN2 TX
DCD CAN2_RX0_IRQHandler ; 64: CAN2 RX0
DCD CAN2_RX1_IRQHandler ; 65: CAN2 RX1
DCD CAN2_SCE_IRQHandler ; 66: CAN2 SCE
DCD OTG_FS_IRQHandler ; 67: USB On-The-Go FS
__Vectors_End
__Vectors_Size EQU __Vectors_End - __Vectors
AREA |.text|, CODE, READONLY
; Reset Handler
Reset_Handler PROC
EXPORT Reset_Handler [WEAK]
IMPORT __main
LDR R0, =__main ; Jump to main()
BX R0
ENDP
; Dummy Exception Handlers (infinite loops which can be modified)
NMI_Handler PROC
EXPORT NMI_Handler [WEAK]
B . ; B . means Branch to this address
ENDP