Difference between revisions of "STM32F107VC/USART"
From Teknologisk videncenter
m (→Links) |
m (→Links) |
||
Line 97: | Line 97: | ||
</source> | </source> | ||
=Links= | =Links= | ||
− | + | *[http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/DATASHEET/CD00002253.pdf ST3232] RS232C Line Driver (Loads PDF) | |
*[http://mars.tekkom.dk/data/USART.zip USART.zip] Keil u-Vision project example using USART | *[http://mars.tekkom.dk/data/USART.zip USART.zip] Keil u-Vision project example using USART | ||
*[http://mars.tekkom.dk/data/USART-Danni.zip USART-Danni.zip] | *[http://mars.tekkom.dk/data/USART-Danni.zip USART-Danni.zip] | ||
[[Category:STM32F107VC]][[Category:ARM]] | [[Category:STM32F107VC]][[Category:ARM]] |
Latest revision as of 07:53, 22 September 2011
Using USART2 on the MCBSTM32C evaluation board
The following example shows minimum configuration of the USART2 using the GPIO port D alternate function.
- prerequisite
- The FCLK bus runs at 72 MHz. See Clock mode 5
/*****************
USART2 remap: USART2_REMAP = 1 - section 9.3.8
PD5 = TX
PD6 = RX
PD4 = RTS
PD3 = CTS
CLOCK = PCLK1 AFTER APB1 PRESCALER
BaudRate = fck / ( 16 * USARTDIV )
Fx:
fck = 36 Mhz
Wanted BuadRate = 9.600
USARTDIV = fck/ (16 * BaudRate ) =
36000000/ (16 * 9600) = 234.375
Mantissa = 234 - as hex = 0xEA
Fraction = 16*0.375 = 6 - as hex 0x6
Step 1: RCC_CFGR bits PPRE1[2:0] = 100 -APB1 Prescaler divide by 2 = 36 MHz
Step 2: RCC_APB2ENR - Enable AFIO Clock - Alternate Clock I/O Enable
Step 3: RCC_APB2ENR - Enable Clock for Port D
Step 4: AFIO_MAPR - Remap USART2 from Port A to Port D
Step 5.1: Enable Port D pin 6 - Floating Input (RX)
Step 5.2: Enable Port D pin 5 - Alternate Function/ Push-Pull Output (TX)
Step 6: RCC_APB1ENR Enable USART2 clock
Step 7.1: USART_BRR bits DIV_Mantissa[11:0] = 0xEA
Step 7.2: USART_BRR bits DIV_fraction[3:0] = 0x6
Step 8: USART_CR1 bit UE - Uart Enable = 1
Step 9: USART_CR1 bit M - Word Length = 0 - 8 bit (Default)
Step 10: USART_CR1 bit WAKE - wake medthod = 0 - Idle Line (Default)
Step 11: USART_CR1 bit PCE - Parity = 0 Parity disabled (Default)
Step 12: USART_CR1 - all interrupts disabled in tiny mode (Default)
Step 13: USART_CR1 bit TE - Tranmitter enable = 1
Step 14: USART_CR1 bit RE - Receiver enable = 1
This config should be sufficient to use the COM port as basic asynchrounous COM port
*/
void usart_enable( void ) {
//Step 1: RCC_CFGR bits PPRE1[2:0] = 100 -APB1 Prescaler divide by 2 = 36 MHz
rcc_cfgr( 0x00000300, 0 ); //Set PPRE1[1:0] = 0
rcc_cfgr( 0x00000400, 1 ); //Set PPRE1[2] = 1
//Step 2: RCC_APB2ENR - Enable AFIO Clock - Alternate Clock I/O Enable
rcc_apb2enr(1 << 0,ENABLE);
//Step 3: RCC_APB2ENR - Enable Clock for Port D
rcc_apb2enr(1 << 5,ENABLE);
//Step 4: AFIO_MAPR - Remap USART2 from Port A to Port D
rcc_afio_mapr(1 << 3, ENABLE);
//Step 5.1 and 5.2 - Enable pin 6 as RX and pin 5 as TX
GPIOD->CRL &= 0xF00FFFFF;
GPIOD->CRL |= 0x04B00000; //Pin 6: 0100 Pin 5: 1011
//Step 6: RCC Enable USART in RCC_APB1ENR
rcc_apb1enr( 1 << 17, ENABLE); //set bit 17 in RCC_APB1ENR (Enable USART2)
//Step 7.1 and 7.2: USART_BRR bits DIV_Mantissa[11:0] = 0xEA and fraction = 6
USART2->BRR = 0x0ea6;
//Step 8: USART_CR1 bit UE - Uart Enable = 1
USART2->CR1 |= 1 << 13;
//Step 13: USART_CR1 bit TE - Tranmitter enable = 1
USART2->CR1 |= 1 << 3;
//Step 14: USART_CR1 bit RE - Receiver enable = 1
USART2->CR1 |= 1 << 2;
}
void usart_tx( char character ) {
while ((USART2->SR & ( 1 << 6)) == 0) {}; // Wait HSERDY = 1
USART2->DR = (uint16_t) character;
}
void puts(char *string) {
int i;
for ( i=0; string[i] != 0; i++ ) {
usart_tx(string[i]);
}
}
Links
- ST3232 RS232C Line Driver (Loads PDF)
- USART.zip Keil u-Vision project example using USART
- USART-Danni.zip