Difference between revisions of "OSPF Cisco IOS/NSSA"
From Teknologisk videncenter
m (Created page with "The following topology is configured on GNS3 on Cisco 7200 Routers {| |800px|left|thumb|Setup |} The Routers have the following configuration: ==R1 ...") |
m (→R1 & R2) |
||
| Line 5: | Line 5: | ||
The Routers have the following configuration: | The Routers have the following configuration: | ||
==R1 & R2== | ==R1 & R2== | ||
| − | {| | + | {| border="1" style="width:100%;" cellspacing="0" |
| − | | | + | |+ Configuration |
| + | |- bgcolor="lightgrey" | ||
| + | ! R1 | ||
| + | ! R2 | ||
| + | |- align="center" | ||
| + | |<source lang=cli> | ||
| + | hostname R1 | ||
| + | ! | ||
| + | ipv6 unicast-routing | ||
| + | ! | ||
| + | interface Loopback0 | ||
| + | ipv6 address 2001::1/128 | ||
| + | ipv6 ospf 1 area 0 | ||
| + | ! | ||
| + | interface FastEthernet0/0 | ||
| + | ipv6 enable | ||
| + | ipv6 ospf 1 area 0 | ||
| + | ! | ||
| + | interface FastEthernet0/1 | ||
| + | no ip address | ||
| + | duplex auto | ||
| + | speed auto | ||
| + | ipv6 enable | ||
| + | ipv6 ospf 1 area 1 | ||
| + | ! | ||
| + | interface FastEthernet1/0 | ||
| + | ipv6 enable | ||
| + | ipv6 ospf 1 area 0 | ||
| + | ! | ||
| + | ! | ||
| + | ipv6 router ospf 1 | ||
| + | router-id 0.0.0.1 | ||
| + | log-adjacency-changes | ||
| + | area 1 nssa | ||
| + | ! | ||
| + | end | ||
| + | |||
| + | R1# | ||
| + | </source> | ||
| + | |<source lang=cli> | ||
| + | R2#show run | ||
| + | hostname R2 | ||
| + | ! | ||
| + | ipv6 unicast-routing | ||
| + | ! | ||
| + | interface Loopback0 | ||
| + | ipv6 address 2001::2/128 | ||
| + | ipv6 ospf 1 area 0 | ||
| + | ! | ||
| + | interface FastEthernet0/0 | ||
| + | ipv6 enable | ||
| + | ipv6 ospf 1 area 0 | ||
| + | ! | ||
| + | interface FastEthernet0/1 | ||
| + | no ip address | ||
| + | duplex auto | ||
| + | speed auto | ||
| + | ipv6 enable | ||
| + | ipv6 ospf 1 area 2 | ||
| + | ! | ||
| + | interface FastEthernet1/0 | ||
| + | ipv6 enable | ||
| + | ipv6 ospf 1 area 0 | ||
| + | ! | ||
| + | ipv6 router ospf 1 | ||
| + | router-id 0.0.0.2 | ||
| + | log-adjacency-changes | ||
| + | area 2 nssa | ||
| + | ! | ||
| + | end | ||
| + | R2# | ||
| + | </source> | ||
|} | |} | ||
| + | == R3 & R4== | ||
| + | == R5 == | ||
| + | {{Source cli}} | ||
Revision as of 14:59, 18 December 2013
The following topology is configured on GNS3 on Cisco 7200 Routers
The Routers have the following configuration:
R1 & R2
| R1 | R2 |
|---|---|
hostname R1
!
ipv6 unicast-routing
!
interface Loopback0
ipv6 address 2001::1/128
ipv6 ospf 1 area 0
!
interface FastEthernet0/0
ipv6 enable
ipv6 ospf 1 area 0
!
interface FastEthernet0/1
no ip address
duplex auto
speed auto
ipv6 enable
ipv6 ospf 1 area 1
!
interface FastEthernet1/0
ipv6 enable
ipv6 ospf 1 area 0
!
!
ipv6 router ospf 1
router-id 0.0.0.1
log-adjacency-changes
area 1 nssa
!
end
R1# |
R2#show run
hostname R2
!
ipv6 unicast-routing
!
interface Loopback0
ipv6 address 2001::2/128
ipv6 ospf 1 area 0
!
interface FastEthernet0/0
ipv6 enable
ipv6 ospf 1 area 0
!
interface FastEthernet0/1
no ip address
duplex auto
speed auto
ipv6 enable
ipv6 ospf 1 area 2
!
interface FastEthernet1/0
ipv6 enable
ipv6 ospf 1 area 0
!
ipv6 router ospf 1
router-id 0.0.0.2
log-adjacency-changes
area 2 nssa
!
end
R2# |