Revision as of 13:46, 19 December 2019

Router

Current configuration : 1179 bytes
!
! Last configuration change at 13:19:45 UTC Thu Dec 19 2019
version 15.2
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
!
no aaa new-model
!
!
ip cef
!
!
!
!
!
!
no ipv6 cef
!
!
license udi pid C881W-E-K9 sn FCZ175191GK
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
interface FastEthernet0
 no ip address
!
interface FastEthernet1
 no ip address
!
interface FastEthernet2
 no ip address
!
interface FastEthernet3
 no ip address
!
interface FastEthernet4
 no ip address
 duplex auto
 speed auto
!
interface Wlan-GigabitEthernet0
 description Internal switch interface connecting to the embedded AP
 no ip address
!
interface wlan-ap0
 description Embedded Service module interface to manage the embedded AP
 ip address 1.1.1.1 255.255.255.255
!
interface Vlan1
 no ip address
!
ip forward-protocol nd
no ip http server
no ip http secure-server
!
!
!
!
!
line con 0
 no modem enable
line aux 0
line 2
 no activation-character
 no exec
 transport preferred none
 transport input all
 stopbits 1
line vty 0 4
 login
 transport input all
!
scheduler allocate 20000 1000
!
end

Wireless

<source lang=text version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname ap ! logging rate-limit console 9 enable secret 5 $1$o7zB$qlOMOhtgDzBOFn/lIqrCR/ ! no aaa new-model ! ! dot11 syslog ! dot11 ssid DataHouse

  vlan 1
  authentication open
  authentication key-management wpa
  mbssid guest-mode
  wpa-psk ascii 0 1234567890

! ! ! username cisco privilege 15 secret 5 $1$HMg/$jbZZPPWzpsTXrtdYKfDhV1 ! ! bridge irb ! ! interface Dot11Radio0

no ip address
no ip route-cache
!
encryption vlan 1 mode ciphers aes-ccm
!
ssid DataHouse
!
antenna gain 0
mbssid
station-role root

! interface Dot11Radio0.1

encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled

! interface GigabitEthernet0

description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router
no ip address
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled

! interface BVI1

ip address dhcp client-id GigabitEthernet0
no ip route-cache

! ip http server no ip http secure-server ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag bridge 1 route ip ! line con 0

privilege level 15
login local
no activation-character

line vty 0 4

login local

! cns dhcp end </source>

@@ Line 172: / Line 172: @@
 ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
 bridge 1 route ip
-!
-!
-banner exec ^CC
-% Password change notice.
------------------------------------------------------------------------
-Default username/password setup on AP is cisco/cisco with privilege level 15.
-It is strongly suggested that you create a new username with privilege level
-using the following command for console security.
-username <myuser> privilege 15 secret 0 <mypassword>
-no username cisco
-Replace <myuser> and <mypassword> with the username and password you want to
-use. After you change your username/password you can turn off this message
-by configuring  "no banner login" and "no banner exec" in privileged mode.
------------------------------------------------------------------------
-^C
-banner login ^CC
-% Password change notice.
------------------------------------------------------------------------
-Default username/password setup on AP is cisco/cisco with privilege level 15.
-It is strongly suggested that you create a new username with privilege level
-using the following command for console security.
-username <myuser> privilege 15 secret 0 <mypassword>
-no username cisco
-Replace <myuser> and <mypassword> with the username and password you want to
-use. After you change your username/password you can turn off this message
-by configuring  "no banner login" and "no banner exec" in privileged mode.
------------------------------------------------------------------------
-^C
 !
 line con 0

Navigation menu

Difference between revisions of "Cisco 881W wireless bridge"

Revision as of 13:46, 19 December 2019

Router

Wireless