Difference between revisions of "Beaglebone Black/Flashing"
From Teknologisk videncenter
m (→Adaption) |
m |
||
| Line 29: | Line 29: | ||
#Login check with ''df -h'' that /dev/mmcblk0p1 is more than 7 GB - if not reboot and check again | #Login check with ''df -h'' that /dev/mmcblk0p1 is more than 7 GB - if not reboot and check again | ||
#apt update and apt upgrade | #apt update and apt upgrade | ||
| + | ==Flasher== | ||
| + | Flasherimage can be used to install/upgrade eMMC flash on BBB boards | ||
| + | #Install [https://mars.merhot.dk/data/bbb/am335x-eMMC-flasher-debian-12.2-iot-armhf-2023-10-07-4gb.img.xz Flasher Image] on microSD card. | ||
| + | #Insert microSD card in BBB you wish to flash | ||
| + | #Press boot switch (Single switch in USB-A end) | ||
| + | #Apply power and hold switch down until LED's blink in squence) | ||
| + | #Wait until it shuts down | ||
| + | |||
| + | |||
==Adaption== | ==Adaption== | ||
*Missing config-pin get https://github.com/beagleboard/bb.org-overlays/blob/master/tools/beaglebone-universal-io/config-pin | *Missing config-pin get https://github.com/beagleboard/bb.org-overlays/blob/master/tools/beaglebone-universal-io/config-pin | ||
Revision as of 13:48, 18 November 2023
Flash microSD kort
Ved opstart af BBB er det vigtigt at du
- Ikke placerer boardet på ledende materiale (Metal fx)
- Tilslutter det serielle kabel - (Sort ledning skal vende op imod ethernet stikket)
- Se billede herunder
- Åbner terminalemulator for eksempel putty eller mobaXterm
- Find COM port nummeret og sæt baudRate til 115200
- Boot fra den indbyggede flash. (microSD kort ikke indsat)
- Login
- sudo bash
- Indsæt microSD kort
- Check at filen /dev/mmcblk0 eksisterer (Undgå at lave en fil)
- wget --no-check-certificate -qO- http://mars.tekkom.dk/data/bbb/bone-debian-10.3-iot-armhf-2020-04-06-4gb.img.xz | xzcat | dd bs=10M of=/dev/mmcblk0 status=progress
- shutdown -r 0
- login
- df -h (Check at det er /dev/mmcblk0p1 der er under /)
- kør /opt/scripts/tools/grow_partition.sh
- shutdown -r 0
- check med df -h at ”/” har cirka 8 GB
- Install debian C linux development tools
Applying new 2023 image
- Remove micro-SD card
- Boot from old-image on on-board flash (mmcblk1)
- insert micro-SD card
- new image: wget --no-check-certificate -qO- https://mars.merhot.dk/data/bbb/am335x-debian-12.2-iot-armhf-2023-10-07-4gb.img.xz | xzcat | dd bs=10M of=/dev/mmcblk0 status=progress
- shutdown -h 0
- Remove power from board
- Login check with df -h that /dev/mmcblk0p1 is more than 7 GB - if not reboot and check again
- apt update and apt upgrade
Flasher
Flasherimage can be used to install/upgrade eMMC flash on BBB boards
- Install Flasher Image on microSD card.
- Insert microSD card in BBB you wish to flash
- Press boot switch (Single switch in USB-A end)
- Apply power and hold switch down until LED's blink in squence)
- Wait until it shuts down
Adaption
- Missing config-pin get https://github.com/beagleboard/bb.org-overlays/blob/master/tools/beaglebone-universal-io/config-pin
- Missing X11 ssh forwarding