Difference between revisions of "WLAN controller Cisco"

From Teknologisk videncenter
Jump to: navigation, search
m (→‎Common links to 2006 and 2811 WLC Links)
m
Line 17: Line 17:
 
= Access Points reboots after config=
 
= Access Points reboots after config=
 
If the LAP's continuesly reboots. Log in on the WLAN controller and start debugging.
 
If the LAP's continuesly reboots. Log in on the WLAN controller and start debugging.
−
<pre>
+
<source lang="cli">
−
R1# service-module wlan-controller 1/0 session
+
R1# <input>service-module wlan-controller 1/0 session</input>
  
−
(WLAN_CONTROLLER) >debug lwapp events enable
+
(WLAN_CONTROLLER) ><input>debug lwapp events enable</input>
  
 
Thu May  7 12:09:40 2009: 00:1b:d4:16:3a:80 Received LWAPP DISCOVERY REQUEST from AP 00:1b:d4:16:3a:80 to 00:15:2c:e9:5f:40 on port '1'
 
Thu May  7 12:09:40 2009: 00:1b:d4:16:3a:80 Received LWAPP DISCOVERY REQUEST from AP 00:1b:d4:16:3a:80 to 00:15:2c:e9:5f:40 on port '1'
Line 39: Line 39:
 
Thu May  7 12:09:51 2009:      [0000] dd 0a 00 c0 b9 01 08 00 00 08 01 01
 
Thu May  7 12:09:51 2009:      [0000] dd 0a 00 c0 b9 01 08 00 00 08 01 01
 
Thu May  7 12:09:52 2009: 00:1b:d4:16:3a:80 Received LWAPP CONFIGURE REQUEST from AP 00:1b:d4:16:3a:80 to  00:15:2c:e9:5f:40
 
Thu May  7 12:09:52 2009: 00:1b:d4:16:3a:80 Received LWAPP CONFIGURE REQUEST from AP 00:1b:d4:16:3a:80 to  00:15:2c:e9:5f:40
−
Thu May  7 12:09:52 2009: 00:1b:d4:16:3a:80 AP 00:1b:d4:16:3a:80: Country code is not configured(AE ).
+
<notice>Thu May  7 12:09:52 2009: 00:1b:d4:16:3a:80 AP 00:1b:d4:16:3a:80: Country code is not configured(AE ).</notice>
−
Thu May  7 12:09:52 2009: 00:1b:d4:16:3a:80 AP 00:1b:d4:16:3a:80: Country code is not configured(AE ).
+
<notice>Thu May  7 12:09:52 2009: 00:1b:d4:16:3a:80 AP 00:1b:d4:16:3a:80: Country code is not configured(AE ).</notice>
 
Thu May  7 12:09:52 2009: 00:1b:d4:16:3a:80 Updating IP info for AP 00:1b:d4:16:3a:80 -- static 0, 172.16.50.173/255.255.255.0, gtw 172.16.50.1
 
Thu May  7 12:09:52 2009: 00:1b:d4:16:3a:80 Updating IP info for AP 00:1b:d4:16:3a:80 -- static 0, 172.16.50.173/255.255.255.0, gtw 172.16.50.1
 
Thu May  7 12:09:52 2009: 00:1b:d4:16:3a:80 Updating IP 172.16.50.173 ===> 172.16.50.173 for AP 00:1b:d4:16:3a:80
 
Thu May  7 12:09:52 2009: 00:1b:d4:16:3a:80 Updating IP 172.16.50.173 ===> 172.16.50.173 for AP 00:1b:d4:16:3a:80
−
Thu May  7 12:09:52 2009: 00:1b:d4:16:3a:80 AP 00:1b:d4:16:3a:80: Country code is not configured(AE ).
+
<notice>Thu May  7 12:09:52 2009: 00:1b:d4:16:3a:80 AP 00:1b:d4:16:3a:80: Country code is not configured(AE ).</notice>
 
Thu May  7 12:09:52 2009: 00:1b:d4:16:3a:80 AP 00:1b:d4:16:3a:80 not allowed to join. Regulatory Domain check failed.
 
Thu May  7 12:09:52 2009: 00:1b:d4:16:3a:80 AP 00:1b:d4:16:3a:80 not allowed to join. Regulatory Domain check failed.
 
Allowed regulatory domain: 802.11bg:-AB    802.11a:-AB
 
Allowed regulatory domain: 802.11bg:-AB    802.11a:-AB
Line 50: Line 50:
 
Thu May  7 12:09:52 2009: 00:1b:d4:16:3a:80 Deregister LWAPP event for AP 00:1b:d4:16:3a:80 slot 0
 
Thu May  7 12:09:52 2009: 00:1b:d4:16:3a:80 Deregister LWAPP event for AP 00:1b:d4:16:3a:80 slot 0
 
Thu May  7 12:09:52 2009: 00:1b:d4:16:3a:80 Deregister LWAPP event for AP 00:1b:d4:16:3a:80 slot 1
 
Thu May  7 12:09:52 2009: 00:1b:d4:16:3a:80 Deregister LWAPP event for AP 00:1b:d4:16:3a:80 slot 1
−
</pre>
+
</source>
 
Note the AP error "Country code is not configured(AE ).".
 
Note the AP error "Country code is not configured(AE ).".
  
 
Finding status of Access Points that dont associate
 
Finding status of Access Points that dont associate
−
<pre>
+
<source lang="cli">
−
(WLAN_CONTROLLER) >show ap join stats summary all
+
(WLAN_CONTROLLER) ><input>show ap join stats summary all</input>
  
 
Number of APs.............................................. 1
 
Number of APs.............................................. 1
Line 61: Line 61:
 
00:1b:d4:16:3a:80.......................................... Not joined
 
00:1b:d4:16:3a:80.......................................... Not joined
  
−
(WLAN_CONTROLLER) show>ap join stats detailed 00:1b:d4:16:3a:80
+
(WLAN_CONTROLLER) show><input>ap join stats detailed 00:1b:d4:16:3a:80</input>
  
 
Discovery phase statistics
 
Discovery phase statistics
Line 95: Line 95:
 
Last join error summary
 
Last join error summary
 
- Type of error that occurred last......................... Lwapp configuration request rejected
 
- Type of error that occurred last......................... Lwapp configuration request rejected
−
- Reason for error that occurred last...................... Regulatory domain check has failed for the AP
+
<notice>- Reason for error that occurred last...................... Regulatory domain check has failed for the AP</notice>
 
- Time at which the last join error occurred............... May 08 12:15:34.930
 
- Time at which the last join error occurred............... May 08 12:15:34.930
−
</pre>
+
</source>
 
== Wrong Country code ==
 
== Wrong Country code ==
 
The IOS installed in the Access Points are regionally, so that all country codes will not work.
 
The IOS installed in the Access Points are regionally, so that all country codes will not work.
 
Too see which channels the controller will try and force the Access Points to use:
 
Too see which channels the controller will try and force the Access Points to use:
−
<pre>
+
<source lang="cli">
−
(Cisco Controller) >show country channels
+
(Cisco Controller) ><input>show country channels</input>
  
  
Line 125: Line 125:
 
  DK (-E)    : . A . A . A . A A A A A A A A A A A A A A A A . . . . .
 
  DK (-E)    : . A . A . A . A A A A A A A A A A A A A A A A . . . . .
 
------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
 
------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
−
</pre>
+
</source>
 
In the example above the Country Code is DK (-E). -E means [http://en.wikipedia.org/wiki/ETSI ETSI (European Telecommunications Standards Institute)] means that the Access Point must support this country setup. That can be seen by the IOS version for example '''AIR-LAP1232AG-E-K9''' the -E means ETSI and it will support European Country codes. Not US (United States)
 
In the example above the Country Code is DK (-E). -E means [http://en.wikipedia.org/wiki/ETSI ETSI (European Telecommunications Standards Institute)] means that the Access Point must support this country setup. That can be seen by the IOS version for example '''AIR-LAP1232AG-E-K9''' the -E means ETSI and it will support European Country codes. Not US (United States)
 
*See [[Media:Aironet1230.pdf|Aironet1230 (Access Point) brochure]]
 
*See [[Media:Aironet1230.pdf|Aironet1230 (Access Point) brochure]]
Line 143: Line 143:
 
*[http://www.cisco.com/en/US/products/hw/wireless/ps430/products_qanda_item09186a00806a4da3.shtml Wireless LAN Controller (WLC) FAQ]
 
*[http://www.cisco.com/en/US/products/hw/wireless/ps430/products_qanda_item09186a00806a4da3.shtml Wireless LAN Controller (WLC) FAQ]
 
*[http://www.cisco.com/en/US/docs/wireless/controller/4.2/configuration/guide/c42lwap.html#wp1147823 LAP Country code]
 
*[http://www.cisco.com/en/US/docs/wireless/controller/4.2/configuration/guide/c42lwap.html#wp1147823 LAP Country code]
 +
{{#css:   
 +
    pre {  font-family: Lucida Console; font-weight: bold; font-size: 14px; color: #00FF00; background: black; margin: 10px 50px; width: 800px; line-height: 200%; overflow: auto;}
 +
}}
 
[[Category:Cisco]][[Category:Network]][[Category:CCNP]][[Category:CCNP3]]
 
[[Category:Cisco]][[Category:Network]][[Category:CCNP]][[Category:CCNP3]]

Revision as of 08:25, 7 July 2009

WLAN Controller model 2006

WLAN controller in 2811 Router

reset controller

  • login as admin password cisco or cisco cisco
  • Enter clear config" command
  • Enter reset system command
  • login as Recover-Config and the system reboots
    • Starts automatically in setup Wizard

Specific Links to 2811 WLC Controller

Access Points reboots after config

If the LAP's continuesly reboots. Log in on the WLAN controller and start debugging. 

R1# <input>service-module wlan-controller 1/0 session</input>

(WLAN_CONTROLLER) ><input>debug lwapp events enable</input>

Thu May  7 12:09:40 2009: 00:1b:d4:16:3a:80 Received LWAPP DISCOVERY REQUEST from AP 00:1b:d4:16:3a:80 to 00:15:2c:e9:5f:40 on port '1'
Thu May  7 12:09:40 2009: 00:1b:d4:16:3a:80 Successful transmission of LWAPP Discovery Response to AP 00:1b:d4:16:3a:80 on port 1
Thu May  7 12:09:51 2009: 00:1b:d4:16:3a:80 Received LWAPP JOIN REQUEST from AP 00:1b:d4:16:3a:80 to 00:15:2c:e9:5f:40 on port '1'
Thu May  7 12:09:51 2009: 00:1b:d4:16:3a:80 AP AP3: txNonce  00:15:2C:E9:5F:40 rxNonce  00:1B:D4:16:3A:80
Thu May  7 12:09:51 2009: 00:1b:d4:16:3a:80 LWAPP Join Request MTU path from AP 00:1b:d4:16:3a:80 is 1500, remote debug mode is 0
Thu May  7 12:09:51 2009: 00:1b:d4:16:3a:80 Successfully added NPU Entry for AP 00:1b:d4:16:3a:80 (index 58)
Switch IP: 172.16.100.100, Switch Port: 12223, intIfNum 1, vlanId 100
AP IP: 172.16.50.173, AP Port: 38389, next hop MAC: 00:1b:54:fb:2e:b0
Thu May  7 12:09:51 2009: 00:1b:d4:16:3a:80 Successful transmission of LWAPP Join Reply to AP 00:1b:d4:16:3a:80
Thu May  7 12:09:51 2009: 00:1b:d4:16:3a:80 spam_lrad.c:1766 - Operation State 0 ===> 4
Thu May  7 12:09:51 2009: 00:1b:d4:16:3a:80 Register LWAPP event for AP 00:1b:d4:16:3a:80 slot 0
Thu May  7 12:09:51 2009: WARP IEs: (12)
Thu May  7 12:09:51 2009:      [0000] dd 0a 00 c0 b9 01 08 00 00 08 01 01
Thu May  7 12:09:51 2009: 00:1b:d4:16:3a:80 Register LWAPP event for AP 00:1b:d4:16:3a:80 slot 1
Thu May  7 12:09:51 2009: WARP IEs: (12)
Thu May  7 12:09:51 2009:      [0000] dd 0a 00 c0 b9 01 08 00 00 08 01 01
Thu May  7 12:09:52 2009: 00:1b:d4:16:3a:80 Received LWAPP CONFIGURE REQUEST from AP 00:1b:d4:16:3a:80 to  00:15:2c:e9:5f:40
<notice>Thu May  7 12:09:52 2009: 00:1b:d4:16:3a:80 AP 00:1b:d4:16:3a:80: Country code is not configured(AE ).</notice>
<notice>Thu May  7 12:09:52 2009: 00:1b:d4:16:3a:80 AP 00:1b:d4:16:3a:80: Country code is not configured(AE ).</notice>
Thu May  7 12:09:52 2009: 00:1b:d4:16:3a:80 Updating IP info for AP 00:1b:d4:16:3a:80 -- static 0, 172.16.50.173/255.255.255.0, gtw 172.16.50.1
Thu May  7 12:09:52 2009: 00:1b:d4:16:3a:80 Updating IP 172.16.50.173 ===> 172.16.50.173 for AP 00:1b:d4:16:3a:80
<notice>Thu May  7 12:09:52 2009: 00:1b:d4:16:3a:80 AP 00:1b:d4:16:3a:80: Country code is not configured(AE ).</notice>
Thu May  7 12:09:52 2009: 00:1b:d4:16:3a:80 AP 00:1b:d4:16:3a:80 not allowed to join. Regulatory Domain check failed.
Allowed regulatory domain: 802.11bg:-AB    802.11a:-AB
Thu May  7 12:09:52 2009: 00:1b:d4:16:3a:80 apfSpamProcessStateChangeInSpamContext: Deregister LWAPP event for AP 00:1b:d4:16:3a:80 slot 0
Thu May  7 12:09:52 2009: 00:1b:d4:16:3a:80 apfSpamProcessStateChangeInSpamContext: Deregister LWAPP event for AP 00:1b:d4:16:3a:80 slot 1
Thu May  7 12:09:52 2009: 00:1b:d4:16:3a:80 Deregister LWAPP event for AP 00:1b:d4:16:3a:80 slot 0
Thu May  7 12:09:52 2009: 00:1b:d4:16:3a:80 Deregister LWAPP event for AP 00:1b:d4:16:3a:80 slot 1

Note the AP error "Country code is not configured(AE ).".

Finding status of Access Points that dont associate 

(WLAN_CONTROLLER) ><input>show ap join stats summary all</input>

Number of APs.............................................. 1

00:1b:d4:16:3a:80.......................................... Not joined

(WLAN_CONTROLLER) show><input>ap join stats detailed 00:1b:d4:16:3a:80</input>

Discovery phase statistics
- Discovery requests received.............................. 12
- Successful discovery responses sent...................... 12
- Unsuccessful discovery request processing................ 2113123
- Reason for last unsuccessful discovery attempt........... None
- Time at last successful discovery attempt................ May 08 12:15:22.772
- Time at last unsuccessful discovery attempt.............. Jan 01 00:00:00.000

Join phase statistics
- Join requests received................................... 12
- Successful join responses sent........................... 12
- Unsuccessful join request processing..................... 0
- Reason for last unsuccessful join attempt................ Not applicable
- Time at last successful join attempt..................... May 08 12:15:33.209
- Time at last unsuccessful join attempt................... Not applicable

Configuration phase statistics
- Configuration requests received.......................... 12
- Successful configuration responses sent.................. 0
- Unsuccessful configuration request processing............ 12
- Reason for last unsuccessful configuration attempt....... Regulatory domain check has failed for the AP
- Time at last successful configuration attempt............ Not applicable
- Time at last unsuccessful configuration attempt.......... May 08 12:15:34.930

Last AP message decrytion failure details
- Reason for last message decryption failure............... Not applicable

Last AP disconnect details
- Reason for last AP connection failure.................... Not applicable

Last join error summary
- Type of error that occurred last......................... Lwapp configuration request rejected
<notice>- Reason for error that occurred last...................... Regulatory domain check has failed for the AP</notice>
- Time at which the last join error occurred............... May 08 12:15:34.930

Wrong Country code

The IOS installed in the Access Points are regionally, so that all country codes will not work. Too see which channels the controller will try and force the Access Points to use: 

(Cisco Controller) ><input>show country channels</input>


Configured Country............................. DK  - Denmark
      KEY: * = Channel is legal in this country and may be configured manually.
           A = Channel is the Auto-RF default in this country.
           . = Channel is not legal in this country.
           C = Channel has been configured for use by Auto-RF.
           x = Channel is available to be configured for use by Auto-RF.
         (-) = Regulatory Domains allowed by this country.
------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
802.11BG    :
Channels    :                   1 1 1 1 1
            : 1 2 3 4 5 6 7 8 9 0 1 2 3 4
------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
 DK (-E)    : A * * * * A * * * * A * * .
------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
 802.11A    :                         1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Channels    : 3 3 3 4 4 4 4 4 5 5 6 6 0 0 0 1 1 2 2 2 3 3 4 4 5 5 6 6
            : 4 6 8 0 2 4 6 8 2 6 0 4 0 4 8 2 6 0 4 8 2 6 0 9 3 7 1 5
------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
 DK (-E)    : . A . A . A . A A A A A A A A A A A A A A A A . . . . .
------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

In the example above the Country Code is DK (-E). -E means ETSI (European Telecommunications Standards Institute) means that the Access Point must support this country setup. That can be seen by the IOS version for example AIR-LAP1232AG-E-K9 the -E means ETSI and it will support European Country codes. Not US (United States)

LAP - Lightweight Access points

LAP 1232AG

QoS on 2006 WLC

Common links to 2006 and 2811 WLC Links

Retrieved from "http://mars.merhot.dk/w/index.php?title=WLAN_controller_Cisco&oldid=7347"