Difference between revisions of "CCNA Explorer semester 2 kapitel 11"
m (→DR og BDR selection example) |
m (→OSPF redistribute OSPF default Route) |
||
Line 178: | Line 178: | ||
|} | |} | ||
− | + | =Reference bandwidth= | |
+ | {| | ||
+ | |[[Image:Ccna explorer 2 chap 11 48.gif|800px|left|thumb|Netværk med internet adgang]] | ||
+ | |- | ||
+ | |[[Image:Ccna explorer 2 chap 11 49.gif|800px|left|thumb|Ændring af reference bandwidth]] | ||
+ | |- | ||
+ | |[[Image:Ccna explorer 2 chap 11 50.gif|800px|left|thumb|Routetabel R1 før ændring]] | ||
+ | |- | ||
+ | |[[Image:Ccna explorer 2 chap 11 51.gif|800px|left|thumb|Routetabel R1 efter ændring]] | ||
+ | |- | ||
+ | |} | ||
[[Category:CCNA]] | [[Category:CCNA]] |
Revision as of 09:49, 18 April 2010
Contents
OSPF Pakketyper
1. Hello - Hello packets are used to establish and maintain adjacency with other OSPF routers. The hello protocol is discussed in detail in the next topic.
2. DBD - The Database Description (DBD) packet contains an abbreviated list of the sending router's link-state database and is used by receiving routers to check against the local link-state database.
3. LSR - Receiving routers can then request more information about any entry in the DBD by sending a Link-State Request (LSR).
4. LSU - Link-State Update (LSU) packets are used to reply to LSRs as well as to announce new information. LSUs contain seven different types of Link-State Advertisements (LSAs). LSUs and LSAs are briefly discussed in a later topic.
5. LSAck - When an LSU is received, the router sends a Link-State Acknowledgement (LSAck) to confirm receipt of the LSU.
HELLO protocol
- Type: OSPF Packet Type: Hello (1), DD (2), LS Request (3), LS Update (4), LS ACK (5)
- Router ID: ID of the originating router
- Area ID: area from which the packet originated
- Network Mask: Subnet mask associated with the sending interface
- Hello Interval: number of seconds between the sending router's hellos
- Router Priority: Used in DR/BDR election (discussed later)
- Designated Router (DR): Router ID of the DR, if any
- Backup Designated Router (BDR): Router ID of the BDR, if any
- List of Neighbors: lists the OSPF Router ID of the neighboring router(s)
Mismatch OSPF timere
Hvis HELLO interval og DEAD interval ikke er ens på naboerne kan der ikke laves et adjacencie.
Link State Updates
OSPF algoritmen
OSPF eksempel
OSPF Router ID
- Use the IP address configured with the OSPF router-id command.
- If the router-id is not configured, the router chooses highest IP address of any of its loopback interfaces.
- If no loopback interfaces are configured, the router chooses highest active IP address of any of its physical interfaces.
Loopback interface OSPF eksempel
Verifying OSPF
- Neighbor ID - The router ID of the neighboring router.
- Pri - The OSPF priority of the interface. This is discussed in a later section.
- State - The OSPF state of the interface. FULL state means that the router and its neighbor have identical OSPF link-state databases. OSPF states are discussed in CCNP.
- Dead Time - The amount of time remaining that the router will wait to receive an OSPF Hello packet from the neighbor before declaring the neighbor down. This value is reset when the interface receives a Hello packet.
- Address - The IP address of the neighbor's interface to which this router is directly connected.
- Interface - The interface on which this router has formed adjacency with the neighbor.