Revision as of 15:10, 15 June 2010

This article is under development....

Maintaining and troubleshooting Campus Switched Solutions

1 This article is under development....
2 Maintaining and troubleshooting Campus Switched Solutions
3 VLAN Troubleshooting
- 3.1 Layer 2 reviewing
  - 3.1.1 ARP
  - 3.1.2 Troubleshooting layer 2
- 3.2 Verifying Layer 2 Forwarding
  - 3.2.1 Often used commands
    - 3.2.1.1 show platform forward interface example
    - 3.2.1.2 traceroute mac
4 Troubleshooting Spanning Tree
- 4.1 Example
- 4.2 Analyzing Spanning Tree
  - 4.2.1 show spanning-tree
5 IP CEF
6 Etherchannel operation
- 6.1 Common Etherchannel problems
- 6.2 Show commands
7 Troubleshooting SVI and Inter-VLAN Routing

VLAN Troubleshooting

Layer 2 reviewing

ARP

show mac-addresses

SW1#<input>show mac-address-table</input>
          Mac Address Table
-------------------------------------------

Vlan    Mac Address       Type        Ports
----    -----------       --------    -----
 All    0100.0ccc.cccc    STATIC      CPU
 All    0100.0ccc.cccd    STATIC      CPU
<notice>...OUTPUT OMITTED...</notice>
   1    001b.0cba.4f99    DYNAMIC     Gi0/9
   1    001b.2a32.2e99    DYNAMIC     Gi0/5
   1    0021.5a7c.5549    DYNAMIC     Gi0/4
   1    00a0.d1e6.60b4    DYNAMIC     Gi0/22
  41    0014.f273.96c0    DYNAMIC     Gi0/7
<notice>...OUTPUT OMITTED...</notice>
  41    001b.0cb6.9141    DYNAMIC     Gi0/7
  41    001b.0cba.4fc1    DYNAMIC     Gi0/9
  41    001b.2a32.2ec1    DYNAMIC     Gi0/5
  12    001f.297d.3460    DYNAMIC     Gi0/2
  20    00a0.c543.035d    DYNAMIC     Gi0/6
  22    0003.47ca.d67c    DYNAMIC     Gi0/7
  22    000c.296c.1120    DYNAMIC     Gi0/12
  24    0016.769f.ff4e    DYNAMIC     Gi0/8
  28    0013.2085.a1fe    DYNAMIC     Gi0/9
  28    0013.2085.c447    DYNAMIC     Gi0/9
<notice>...OUTPUT OMITTED...</notice>

Troubleshooting layer 2

Hardware issues (move cable to good port)
VLAN configuration.
- Inter-VLAN traffic must be routed
Trunk configuration
- Same trunkprotocol (DOT1Q,ISL)
- Same Native VLAN

Verifying Layer 2 Forwarding

Often used commands

show mac-address-table
show vlan
show interface trunk
show interface switchport
show platform forward interface - Example below
traceroute mac - Example below

show platform forward interface example

Show how the switch will direct traffic

SW1#<input>show platform forward gigabitEthernet 0/1 vlan 1 0021.5a7c.5549 001b.2a32.2e99</input>
Ingress:
Global Port Number: 1, lpn: 3 Asic Number: 1
Source Vlan Id: Real 1, Mapped 1. L2EncapType 0, L3EncapType 3
Hashes: L2Src 0x00 L2Dst 0x09 L3Src 0x00 L3Dst 0x09
 Lookup                   Key-Used                  Index-Hit    A-Data
Classify 68_0070001B_2A322E99-00_00000021_5A7C5549     00FFC   00000000
InputACL 20_0070001B_2A322E99-00_00000021_5A7C5549     01FF8   01000000
L2LrnMsk FF_03FFFFFF_FFFFFFFF-00_000003FF_00000000
L2Learn  83_00010021_5A7C5549-93_00000401_00000000     01840   00000000
L2FwdMsk FF_03FFFFFF_FFFFFFFF
L2Fwd    83_0001001B_2A322E99                          0003E   000000C5
Station Descriptor: F005F001, DestIndex: F005, RewriteIndex: F001
==========================================
Egress: Asic 0, switch 1
Source Vlan Id: Real 1, Mapped 1. L2EncapType 0, L3EncapType 3
portMap 0x4, non-SPAN portMap 0x4

Output Packets:
------------------------------------------
GigabitEthernet0/5 Packet 1
 Lookup                   Key-Used                  Index-Hit    A-Data
OutptACL 30_0070001B_2A322E99-00_00000021_5A7C5549     01FFC   01000000

Port       Vlan      SrcMac          DstMac    Cos  Dscpv
Gi0/5      0001 0021.5a7c.5549  001b.2a32.2e99

traceroute mac

Did not work out all right.

SW1#<input>traceroute mac 001b.0c5d.42c2 0006.5bc5.2dfb</input>
l2trace error response received : 3 from 192.168.4.22
Layer2 path not through SW2 [192.168.4.22].
Layer2 trace aborted.

Troubleshooting Spanning Tree

Example

insert figure 4-9 on page 112

Elect a root bridge
1. based in lowest BID
Select a root port on each switch.
1. Least cost to Root bridge
  1. Ties broken by lowest upstream BID
  2. Further ties are broken by lowest port ID
Elect a designated device/port on each network segment
1. Based on lowest cost to Root bridge.
  1. Ties are broken on BID
  2. Further ties are broken by lowest port ID
Ports that ended up as neither a root port nor a designated port go into [[Spanning_tree_protocol#STP_Port_States|blocking] state

Analyzing Spanning Tree

See Spanning tree protocol

show spanning-tree

SW1#<input>show spanning-tree vlan 10</input>
MST01
  Spanning tree enabled protocol mstp
  Root ID    Priority    24577
             Address     0019.e751.0880
             <notice>This bridge is the root</notice>
             Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec

  Bridge ID  Priority    24577  (priority 24576 sys-id-ext 1)
             Address     0019.e751.0880
             Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec

Interface        Role Sts Cost      Prio.Nbr Type
---------------- ---- --- --------- -------- --------------------------------
Gi0/1            Desg FWD 20000     128.1    P2p
Gi0/2            Desg FWD 20000     128.2    P2p
Gi0/12           Desg FWD 20000     128.12   P2p

Another example

SW1#<input>show spanning-tree interface gigabitEthernet 0/2 detail</input>
 Port 2 (GigabitEthernet0/2) of <notice>MST00</notice> is designated forwarding
   Port path cost 20000, Port priority 128, Port Identifier 128.2.
   Designated root has priority 32768, address 0014.f273.96c0
   Designated bridge has priority 32768, address 0019.e751.0880
   Designated port id is 128.2, designated path cost 0
   Timers: message age 0, forward delay 0, hold 0
   Number of transitions to forwarding state: 2
   Link type is point-to-point by default, Internal
   Bpdu filter is enabled internally
   BPDU: sent 1530609, received 9

 Port 2 (GigabitEthernet0/2) of <notice>MST01</notice> is designated forwarding
   Port path cost 20000, Port priority 128, Port Identifier 128.2.
   Designated root has priority 24577, address 0019.e751.0880
   Designated bridge has priority 24577, address 0019.e751.0880
   Designated port id is 128.2, designated path cost 0
   Timers: message age 0, forward delay 0, hold 0
   Number of transitions to forwarding state: 2
   Link type is point-to-point by default, Internal
   Bpdu filter is enabled internally
   BPDU: sent 1530609, received 9

IP CEF

3560 Switch platform

CEF

show ip cef 0.0.0.0 0.0.0.0 internal

SW1#<input>show cef fib</input>
119 allocated IPv4 entries, 0 failed allocations

SW1#<input>show ip cef switching statistics</input>

       Reason                          Drop       Punt  Punt2Host
RP RIB Packet destined for us             0    1412459          0
RP RIB Total                              0    1412459          0

RP LES No adjacency                    6399          0     100446
RP LES TTL expired                        0          0         36
RP LES Total                           6399          0     100482

All    Total                           6399    1412459     100482

SW1#<input>show ip cef vrf * summary</input>
IPv4 CEF is enabled for distributed and running
VRF Default:
 130 prefixes (130/0 fwd/non-fwd)
 Default network 0.0.0.0/0
 Table id 0, 0 resets
 Database epoch: 1 (130 entries at this epoch)

Heimdal#<input>sh ip cef</input>
Prefix               Next Hop             Interface
0.0.0.0/0            172.16.4.1
0.0.0.0/32           receive
172.16.4.0/24        attached             Vlan1
172.16.4.0/32        receive
172.16.4.1/32        attached             Vlan1
172.16.4.5/32        attached             Vlan1
172.16.4.15/32       attached             Vlan1
172.16.4.16/32       attached             Vlan1
172.16.4.20/32       receive
172.16.4.22/32       attached             Vlan1
172.16.4.233/32      attached             Vlan1
172.16.4.254/32      attached             Vlan1
172.16.4.255/32      receive
192.168.22.0/24      172.16.4.16
192.168.128.0/24     attached             Vlan10
192.168.128.0/32     receive
192.168.128.1/32     receive
192.168.128.255/32   receive
192.168.130.0/24     attached             Vlan12
192.168.130.0/32     receive
192.168.130.1/32     receive
192.168.130.126/32   attached             Vlan12
192.168.138.149/32   attached             Vlan20
192.168.138.255/32   receive
192.168.140.0/24     attached             Vlan22
<notice>...OUTPUT OMITTED...</notice>

Adjacency table

SW1#<input>show adjacency</input>
Protocol Interface                 Address
IP       Vlan1                     172.16.4.5(7)
IP       Vlan1                     stella.tekkom.dk(7)
IP       Vlan1                     mars(9)
IP       Vlan1                     172.16.4.50(9)
IP       Vlan1                     172.16.4.60(9)
IP       Vlan1                     172.16.4.66(7)
IP       Vlan12                    192.168.130.126(7)
IP       Vlan12                    hot-pc-gf.tekkom.local(7)
IP       Vlan28                    192.168.146.145(7)
IP       Vlan28                    192.168.146.146(7)
IP       Vlan28                    192.168.146.149(7)
IP       Vlan28                    192.168.146.150(7)
IP       Vlan28                    192.168.146.151(7)

Looking at details

SW1#<input>show adjacency 172.16.4.16 detail</input>
Protocol Interface                 Address
IP       Vlan1                     mars(9)
                                   0 packets, 0 bytes
                                   epoch 0
                                   sourced in sev-epoch 4874
                                   Encap length 14
                                   <notice>0007E9400ABF</notice>0019E75108C00800
                                   ARP
SW1#<input>sh arp | inc 172.16.4.16</input>
Internet  172.16.4.16             1   <notice>0007.e940.0abf</notice>  ARPA   Vlan1

Notes

If you enable CEF and then create an access list that uses the log keyword, the packets that match the access list are not CEF switched. They are fast switched. Logging disables CEF.

http://www.cisco.com/en/US/docs/ios/12_2/switch/configuration/guide/xcfcef.html

Links

See [1]

Etherchannel operation

See EtherChannel

Common Etherchannel problems

Inconsistensies between the physical ports that are member of a channel

Must have same speed, duplex, trunk or access port status.
- Same native VLAN when trunking
- Same access VLAN when access port

Log message

%EC-5-CANNOT_BUNDLE2

Inconsistensies between the ports on the opposite sides of the EtherChannel link

If the switch on the other side is not configured to a etherchannel by discovering inconsistencies in the spanning tree.

Log message

%SPANTREE-2-CHNL_MISCFG

Uneven distribution of traffic between EtherChannel bundle members

See EtherChannel#Distributing_traffic_in_the_EtherChannel

Show commands

show etherchannel summary
show etherchannel 1 detail

Troubleshooting SVI and Inter-VLAN Routing

@@ Line 150: / Line 150: @@
     BPDU: sent 1530609, received 9
 </source>
+=IP CEF=
 {{:IP CEF Cisco}}

Navigation menu

Difference between revisions of "CCNP TSHOOT Learning Guide/Chapter 4"

Revision as of 15:10, 15 June 2010

This article is under development....

Maintaining and troubleshooting Campus Switched Solutions

Contents

VLAN Troubleshooting

Layer 2 reviewing

ARP

Troubleshooting layer 2

Verifying Layer 2 Forwarding

Often used commands

show platform forward interface example

traceroute mac

Troubleshooting Spanning Tree

Example

Analyzing Spanning Tree

show spanning-tree

IP CEF

3560 Switch platform

CEF

Adjacency table

Notes

Links

Etherchannel operation

Common Etherchannel problems

Inconsistensies between the physical ports that are member of a channel

Log message

Inconsistensies between the ports on the opposite sides of the EtherChannel link

Log message

Uneven distribution of traffic between EtherChannel bundle members

Show commands

Troubleshooting SVI and Inter-VLAN Routing