Difference between revisions of "CCNP TSHOOT Learning Guide/Chapter 4"

From Teknologisk videncenter
Jump to: navigation, search
m
m
 
(16 intermediate revisions by the same user not shown)
Line 50: Line 50:
 
*traceroute mac - Example below
 
*traceroute mac - Example below
 
==== show platform forward ''interface'' example ====
 
==== show platform forward ''interface'' example ====
 +
 +
Show how the switch will direct traffic
 
<source lang=cli>
 
<source lang=cli>
−
Show how the switch will direct traffic
 
 
SW1#<input>show platform forward gigabitEthernet 0/1 vlan 1 0021.5a7c.5549 001b.2a32.2e99</input>
 
SW1#<input>show platform forward gigabitEthernet 0/1 vlan 1 0021.5a7c.5549 001b.2a32.2e99</input>
 
Ingress:
 
Ingress:
Line 79: Line 80:
 
Gi0/5      0001 0021.5a7c.5549  001b.2a32.2e99
 
Gi0/5      0001 0021.5a7c.5549  001b.2a32.2e99
 
</source>
 
</source>
−
Between two MAC-addresses in two different VLANs in a layer 3 switch
+
====traceroute mac====
 +
Did not work out all right.
 
<source lang=cli>
 
<source lang=cli>
−
Heimdal#show platform forward gigabitEthernet 0/1 vlan 1 0021.5a7c.5549 000c.29ca.39dd
+
SW1#<input>traceroute mac 001b.0c5d.42c2 0006.5bc5.2dfb</input>
−
Ingress:
+
l2trace error response received : 3 from 192.168.4.22
−
Global Port Number: 1, lpn: 3 Asic Number: 1
+
Layer2 path not through SW2 [192.168.4.22].
−
Source Vlan Id: Real 1, Mapped 1. L2EncapType 0, L3EncapType 3
+
Layer2 trace aborted.
−
Hashes: L2Src 0x00 L2Dst 0x0A L3Src 0x00 L3Dst 0x0A
+
</source>
−
Lookup                  Key-Used                  Index-Hit    A-Data
+
=Troubleshooting Spanning Tree=
−
Classify 68_0070000C_29CA39DD-00_00000021_5A7C5549    00FFC  00000000
+
==Example==
−
InputACL 20_0070000C_29CA39DD-00_00000021_5A7C5549    01FF8  01000000
+
'''insert figure 4-9 on page 112'''
−
L2LrnMsk FF_03FFFFFF_FFFFFFFF-00_000003FF_00000000
+
#Elect a root bridge
−
L2Learn  83_00010021_5A7C5549-93_00000401_00000000    01840  00000000
+
##based in lowest [[Spanning_tree_protocol#BID_or_Bridge_Identifier|BID]]
−
L2FwdMsk FF_03FFFFFF_FFFFFFFF
+
#Select a root port on each switch.
−
L2Fwd    83_0001000C_29CA39DD                          01840  0000003C
+
##Least cost to [[Spanning_tree_protocol#Selection_of_Root_Bridge|Root]] bridge
−
Station Descriptor: 02E70000, DestIndex: 02E8, RewriteIndex: F001
+
###Ties broken by lowest upstream [[Spanning_tree_protocol#BID_or_Bridge_Identifier|BID]]
−
==========================================
+
###Further ties are broken by lowest port ID
−
Egress: Asic 0, switch 1
+
#Elect a designated device/port on each network segment
−
Source Vlan Id: Real 1, Mapped 1. L2EncapType 0, L3EncapType 3
+
##Based on lowest cost to Root bridge.
−
portMap 0xF, non-SPAN portMap 0xF
+
###Ties are broken on [[Spanning_tree_protocol#BID_or_Bridge_Identifier|BID]]
 +
###Further ties are broken by lowest port ID
 +
#Ports that ended up as neither a root port nor a designated port go into [[Spanning_tree_protocol#STP_Port_States|blocking] state
  
−
Output Packets:
+
==Analyzing Spanning Tree==
−
------------------------------------------
+
*See [[Spanning tree protocol]]
−
GigabitEthernet0/7 Packet 1
+
=== show spanning-tree ===
−
Lookup                  Key-Used                  Index-Hit   A-Data
+
<source lang=cli>
−
OutptACL 30_0070000C_29CA39DD-00_00000021_5A7C5549     01FFC   01000000
+
SW1#<input>show spanning-tree vlan 10</input>
 +
MST01
 +
  Spanning tree enabled protocol mstp
 +
  Root ID    Priority   24577
 +
            Address     0019.e751.0880
 +
            <notice>This bridge is the root</notice>
 +
            Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec
  
−
Port      Vlan      SrcMac          DstMac   Cos Dscpv
+
  Bridge ID  Priority   24577 (priority 24576 sys-id-ext 1)
−
Gi0/7      0001 0021.5a7c.5549  000c.29ca.39dd
+
            Address    0019.e751.0880
−
------------------------------------------
+
            Hello Time  2 sec  Max Age 20 sec Forward Delay 15 sec
−
GigabitEthernet0/8 Packet 2
 
−
  Lookup                  Key-Used                  Index-Hit    A-Data
 
−
OutptACL 30_0070000C_29CA39DD-00_00000021_5A7C5549    01FFC  01000000
 
  
−
Port      Vlan     SrcMac          DstMac    Cos  Dscpv
+
Interface        Role Sts Cost     Prio.Nbr Type
−
Gi0/8      0001 0021.5a7c.5549  000c.29ca.39dd
+
---------------- ---- --- --------- -------- --------------------------------
−
------------------------------------------
+
Gi0/1            Desg FWD 20000    128.1    P2p
−
GigabitEthernet0/5 Packet 3
+
Gi0/2            Desg FWD 20000    128.2    P2p
−
Lookup                  Key-Used                  Index-Hit   A-Data
+
Gi0/12          Desg FWD 20000    128.12  P2p
−
OutptACL 30_0070000C_29CA39DD-00_00000021_5A7C5549    01FFC  01000000
+
</source>
 +
Another example
 +
<source lang=cli>
 +
SW1#<input>show spanning-tree interface gigabitEthernet 0/2 detail</input>
 +
Port 2 (GigabitEthernet0/2) of <notice>MST00</notice> is designated forwarding
 +
  Port path cost 20000, Port priority 128, Port Identifier 128.2.
 +
  Designated root has priority 32768, address 0014.f273.96c0
 +
  Designated bridge has priority 32768, address 0019.e751.0880
 +
  Designated port id is 128.2, designated path cost 0
 +
  Timers: message age 0, forward delay 0, hold 0
 +
  Number of transitions to forwarding state: 2
 +
  Link type is point-to-point by default, Internal
 +
   Bpdu filter is enabled internally
 +
  BPDU: sent 1530609, received 9
  
−
Port       Vlan      SrcMac          DstMac   Cos  Dscpv
+
Port 2 (GigabitEthernet0/2) of <notice>MST01</notice> is designated forwarding
−
Gi0/5      0001 0021.5a7c.5549  000c.29ca.39dd
+
   Port path cost 20000, Port priority 128, Port Identifier 128.2.
−
------------------------------------------
+
  Designated root has priority 24577, address 0019.e751.0880
−
GigabitEthernet0/6 Packet 4
+
  Designated bridge has priority 24577, address 0019.e751.0880
−
Lookup                  Key-Used                  Index-Hit    A-Data
+
  Designated port id is 128.2, designated path cost 0
−
OutptACL 30_0070000C_29CA39DD-00_00000021_5A7C5549    01FFC  01000000
+
  Timers: message age 0, forward delay 0, hold 0
 +
  Number of transitions to forwarding state: 2
 +
  Link type is point-to-point by default, Internal
 +
  Bpdu filter is enabled internally
 +
  BPDU: sent 1530609, received 9
 +
</source>
 +
=IP CEF=
 +
{{:IP CEF Cisco}}
  
−
Port      Vlan      SrcMac          DstMac    Cos  Dscpv
+
=Etherchannel operation=
−
Gi0/6      0001 0021.5a7c.5549  000c.29ca.39dd
+
*See [[EtherChannel]]
−
==========================================
+
==Common Etherchannel problems==
−
Egress: Asic 1, switch 1
+
===Inconsistensies between the physical ports that are member of a channel===
−
Source Vlan Id: Real 1, Mapped 1. L2EncapType 0, L3EncapType 3
+
*Must have same speed, duplex, trunk or access port status.
−
portMap 0xD, non-SPAN portMap 0xD
+
**Same native VLAN when trunking
 +
**Same access VLAN when access port
 +
====Log message====
 +
%EC-5-CANNOT_BUNDLE2
 +
===Inconsistensies between the ports on the opposite sides of the EtherChannel link===
 +
If the switch on the other side is not configured to a etherchannel by discovering inconsistencies in the spanning tree.
 +
====Log message====
 +
%SPANTREE-2-CHNL_MISCFG
 +
===Uneven distribution of traffic between EtherChannel bundle members===
 +
See [[EtherChannel#Distributing_traffic_in_the_EtherChannel]]
 +
==Show commands==
 +
*show etherchannel summary
 +
*show etherchannel 1 detail
  
−
Output Packets:
+
= Troubleshooting SVI and Inter-VLAN Routing=
−
------------------------------------------
 
−
GigabitEthernet0/2 Packet 5
 
−
Lookup                  Key-Used                  Index-Hit    A-Data
 
−
OutptACL 30_0070000C_29CA39DD-00_00000021_5A7C5549    01FFC  01000000
 
  
−
Port      Vlan      SrcMac          DstMac    Cos  Dscpv
+
= First HOP Routing Protocols =
−
Gi0/2      0001 0021.5a7c.5549  000c.29ca.39dd
+
*[[FHRP]]
−
------------------------------------------
+
== Verifying FHRP Operation ==
−
GigabitEthernet0/4 Packet 6
+
=== HSRP===
−
Lookup                  Key-Used                  Index-Hit    A-Data
+
*See [[HSRP]]
−
OutptACL 30_0070000C_29CA39DD-00_00000021_5A7C5549    01FFC  01000000
+
*show standby brief
−
 
+
*show standby fa0/0
−
Port      Vlan      SrcMac          DstMac    Cos  Dscpv
+
*debug standby terse
−
Gi0/4      0001 0021.5a7c.5549  000c.29ca.39dd
+
=== VRRP ===
−
------------------------------------------
+
*See [[VRRP]]
−
GigabitEthernet0/1 Packet 7
+
*show vrrp brief
−
Lookup                  Key-Used                  Index-Hit    A-Data
+
===GLBP===
−
OutptACL 30_0070000C_29CA39DD-00_00000021_5A7C5549    01FFC  01000000
+
*See [[GLBP]]
−
Dropped due to failed deja vu check.
+
*show glbp brief
−
==========================================
+
{{Source cli}}
−
Egress: Asic 2, switch 1
 
−
Source Vlan Id: Real 1, Mapped 1. L2EncapType 0, L3EncapType 3
 
−
portMap 0x4, non-SPAN portMap 0x4
 
−
 
 
−
Output Packets:
 
−
------------------------------------------
 
−
GigabitEthernet0/13 Packet 8
 
−
Lookup                  Key-Used                  Index-Hit    A-Data
 
−
OutptACL 30_0070000C_29CA39DD-00_00000021_5A7C5549    01FFC  01000000
 
−
 
 
−
Port      Vlan      SrcMac          DstMac    Cos  Dscpv
 
−
Gi0/13    0001 0021.5a7c.5549  000c.29ca.39dd
 
−
==========================================
 
−
Egress: Asic 3, switch 1
 
−
Source Vlan Id: Real 1, Mapped 1. L2EncapType 0, L3EncapType 3
 
−
portMap 0xE, non-SPAN portMap 0xE
 
−
 
 
−
Output Packets:
 
−
------------------------------------------
 
−
GigabitEthernet0/11 Packet 9
 
−
Lookup                  Key-Used                  Index-Hit    A-Data
 
−
OutptACL 30_0070000C_29CA39DD-00_00000021_5A7C5549    01FFC  01000000
 
−
 
 
−
Port      Vlan      SrcMac          DstMac    Cos  Dscpv
 
−
Gi0/11    0001 0021.5a7c.5549  000c.29ca.39dd
 
−
------------------------------------------
 
−
GigabitEthernet0/12 Packet 10
 
−
Lookup                  Key-Used                  Index-Hit    A-Data
 
−
OutptACL 30_0070000C_29CA39DD-00_00000021_5A7C5549    01FFC  01000000
 
−
 
 
−
Port      Vlan      SrcMac          DstMac    Cos  Dscpv
 
−
Gi0/12    0001 0021.5a7c.5549  000c.29ca.39dd
 
−
------------------------------------------
 
−
GigabitEthernet0/9 Packet 11
 
−
Lookup                  Key-Used                  Index-Hit    A-Data
 
−
OutptACL 30_0070000C_29CA39DD-00_00000021_5A7C5549    01FFC  01000000
 
−
 
 
−
Port      Vlan      SrcMac          DstMac    Cos  Dscpv
 
−
Gi0/9      0001 0021.5a7c.5549  000c.29ca.39dd
 
−
==========================================
 
−
Egress: Asic 5, switch 1
 
−
Source Vlan Id: Real 1, Mapped 1. L2EncapType 0, L3EncapType 3
 
−
portMap 0x9, non-SPAN portMap 0x9
 
  
−
Output Packets:
+
[[Category:CCNPv6]][[Category:CCNPv6 TSHOOT]]
−
------------------------------------------
 
−
GigabitEthernet0/23 Packet 12
 
−
Lookup                  Key-Used                  Index-Hit    A-Data
 
−
OutptACL 30_0070000C_29CA39DD-00_00000021_5A7C5549    01FFC  01000000
 
−
 
 
−
Port      Vlan      SrcMac          DstMac    Cos  Dscpv
 
−
Gi0/23    0001 0021.5a7c.5549  000c.29ca.39dd
 
−
------------------------------------------
 
−
GigabitEthernet0/22 Packet 13
 
−
Lookup                  Key-Used                  Index-Hit    A-Data
 
−
OutptACL 30_0070000C_29CA39DD-00_00000021_5A7C5549    01FFC  01000000
 
−
 
 
−
Port      Vlan      SrcMac          DstMac    Cos  Dscpv
 
−
Gi0/22    0001 0021.5a7c.5549  000c.29ca.39dd
 
−
==========================================
 
−
Egress: Asic 6, switch 1
 
−
Source Vlan Id: Real 1, Mapped 1. L2EncapType 0, L3EncapType 3
 
−
portMap 0x6, non-SPAN portMap 0x6
 
−
 
 
−
Output Packets:
 
−
------------------------------------------
 
−
GigabitEthernet0/19 Packet 14
 
−
Lookup                  Key-Used                  Index-Hit    A-Data
 
−
OutptACL 30_0070000C_29CA39DD-00_00000021_5A7C5549    01FFC  01000000
 
−
 
 
−
Port      Vlan      SrcMac          DstMac    Cos  Dscpv
 
−
Gi0/19    0001 0021.5a7c.5549  000c.29ca.39dd
 
−
------------------------------------------
 
−
GigabitEthernet0/20 Packet 15
 
−
Lookup                  Key-Used                  Index-Hit    A-Data
 
−
OutptACL 30_0070000C_29CA39DD-00_00000021_5A7C5549    01FFC  01000000
 
−
 
 
−
Port      Vlan      SrcMac          DstMac    Cos  Dscpv
 
−
Gi0/20    0001 0021.5a7c.5549  000c.29ca.39dd
 
−
</source>
 
−
{{Source cli}}
 

Latest revision as of 15:15, 16 June 2010

Kate.png This article is under development....

Maintaining and troubleshooting Campus Switched Solutions

VLAN Troubleshooting

Layer 2 reviewing

ARP

  • show mac-addresses
SW1#<input>show mac-address-table</input>
          Mac Address Table
-------------------------------------------

Vlan    Mac Address       Type        Ports
----    -----------       --------    -----
 All    0100.0ccc.cccc    STATIC      CPU
 All    0100.0ccc.cccd    STATIC      CPU
<notice>...OUTPUT OMITTED...</notice>
   1    001b.0cba.4f99    DYNAMIC     Gi0/9
   1    001b.2a32.2e99    DYNAMIC     Gi0/5
   1    0021.5a7c.5549    DYNAMIC     Gi0/4
   1    00a0.d1e6.60b4    DYNAMIC     Gi0/22
  41    0014.f273.96c0    DYNAMIC     Gi0/7
<notice>...OUTPUT OMITTED...</notice>
  41    001b.0cb6.9141    DYNAMIC     Gi0/7
  41    001b.0cba.4fc1    DYNAMIC     Gi0/9
  41    001b.2a32.2ec1    DYNAMIC     Gi0/5
  12    001f.297d.3460    DYNAMIC     Gi0/2
  20    00a0.c543.035d    DYNAMIC     Gi0/6
  22    0003.47ca.d67c    DYNAMIC     Gi0/7
  22    000c.296c.1120    DYNAMIC     Gi0/12
  24    0016.769f.ff4e    DYNAMIC     Gi0/8
  28    0013.2085.a1fe    DYNAMIC     Gi0/9
  28    0013.2085.c447    DYNAMIC     Gi0/9
<notice>...OUTPUT OMITTED...</notice>

Troubleshooting layer 2

  • Hardware issues (move cable to good port)
  • VLAN configuration.
    • Inter-VLAN traffic must be routed
  • Trunk configuration
    • Same trunkprotocol (DOT1Q,ISL)
    • Same Native VLAN

Verifying Layer 2 Forwarding

Often used commands

  • show mac-address-table
  • show vlan
  • show interface trunk
  • show interface switchport
  • show platform forward interface - Example below
  • traceroute mac - Example below

show platform forward interface example

Show how the switch will direct traffic 

SW1#<input>show platform forward gigabitEthernet 0/1 vlan 1 0021.5a7c.5549 001b.2a32.2e99</input>
Ingress:
Global Port Number: 1, lpn: 3 Asic Number: 1
Source Vlan Id: Real 1, Mapped 1. L2EncapType 0, L3EncapType 3
Hashes: L2Src 0x00 L2Dst 0x09 L3Src 0x00 L3Dst 0x09
 Lookup                   Key-Used                  Index-Hit    A-Data
Classify 68_0070001B_2A322E99-00_00000021_5A7C5549     00FFC   00000000
InputACL 20_0070001B_2A322E99-00_00000021_5A7C5549     01FF8   01000000
L2LrnMsk FF_03FFFFFF_FFFFFFFF-00_000003FF_00000000
L2Learn  83_00010021_5A7C5549-93_00000401_00000000     01840   00000000
L2FwdMsk FF_03FFFFFF_FFFFFFFF
L2Fwd    83_0001001B_2A322E99                          0003E   000000C5
Station Descriptor: F005F001, DestIndex: F005, RewriteIndex: F001
==========================================
Egress: Asic 0, switch 1
Source Vlan Id: Real 1, Mapped 1. L2EncapType 0, L3EncapType 3
portMap 0x4, non-SPAN portMap 0x4

Output Packets:
------------------------------------------
GigabitEthernet0/5 Packet 1
 Lookup                   Key-Used                  Index-Hit    A-Data
OutptACL 30_0070001B_2A322E99-00_00000021_5A7C5549     01FFC   01000000

Port       Vlan      SrcMac          DstMac    Cos  Dscpv
Gi0/5      0001 0021.5a7c.5549  001b.2a32.2e99

traceroute mac

Did not work out all right. 

SW1#<input>traceroute mac 001b.0c5d.42c2 0006.5bc5.2dfb</input>
l2trace error response received : 3 from 192.168.4.22
Layer2 path not through SW2 [192.168.4.22].
Layer2 trace aborted.

Troubleshooting Spanning Tree

Example

insert figure 4-9 on page 112

  1. Elect a root bridge
    1. based in lowest BID
  2. Select a root port on each switch.
    1. Least cost to Root bridge
      1. Ties broken by lowest upstream BID
      2. Further ties are broken by lowest port ID
  3. Elect a designated device/port on each network segment
    1. Based on lowest cost to Root bridge.
      1. Ties are broken on BID
      2. Further ties are broken by lowest port ID
  4. Ports that ended up as neither a root port nor a designated port go into [[Spanning_tree_protocol#STP_Port_States|blocking] state

Analyzing Spanning Tree

show spanning-tree

SW1#<input>show spanning-tree vlan 10</input>
MST01
  Spanning tree enabled protocol mstp
  Root ID    Priority    24577
             Address     0019.e751.0880
             <notice>This bridge is the root</notice>
             Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec

  Bridge ID  Priority    24577  (priority 24576 sys-id-ext 1)
             Address     0019.e751.0880
             Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec

Interface        Role Sts Cost      Prio.Nbr Type
---------------- ---- --- --------- -------- --------------------------------
Gi0/1            Desg FWD 20000     128.1    P2p
Gi0/2            Desg FWD 20000     128.2    P2p
Gi0/12           Desg FWD 20000     128.12   P2p

Another example 

SW1#<input>show spanning-tree interface gigabitEthernet 0/2 detail</input>
 Port 2 (GigabitEthernet0/2) of <notice>MST00</notice> is designated forwarding
   Port path cost 20000, Port priority 128, Port Identifier 128.2.
   Designated root has priority 32768, address 0014.f273.96c0
   Designated bridge has priority 32768, address 0019.e751.0880
   Designated port id is 128.2, designated path cost 0
   Timers: message age 0, forward delay 0, hold 0
   Number of transitions to forwarding state: 2
   Link type is point-to-point by default, Internal
   Bpdu filter is enabled internally
   BPDU: sent 1530609, received 9

 Port 2 (GigabitEthernet0/2) of <notice>MST01</notice> is designated forwarding
   Port path cost 20000, Port priority 128, Port Identifier 128.2.
   Designated root has priority 24577, address 0019.e751.0880
   Designated bridge has priority 24577, address 0019.e751.0880
   Designated port id is 128.2, designated path cost 0
   Timers: message age 0, forward delay 0, hold 0
   Number of transitions to forwarding state: 2
   Link type is point-to-point by default, Internal
   Bpdu filter is enabled internally
   BPDU: sent 1530609, received 9

IP CEF

3560 Switch platform

CEF

  • show ip cef 0.0.0.0 0.0.0.0 internal
SW1#<input>show cef fib</input>
119 allocated IPv4 entries, 0 failed allocations
SW1#<input>show ip cef switching statistics</input>

       Reason                          Drop       Punt  Punt2Host
RP RIB Packet destined for us             0    1412459          0
RP RIB Total                              0    1412459          0

RP LES No adjacency                    6399          0     100446
RP LES TTL expired                        0          0         36
RP LES Total                           6399          0     100482

All    Total                           6399    1412459     100482
SW1#<input>show ip cef vrf * summary</input>
IPv4 CEF is enabled for distributed and running
VRF Default:
 130 prefixes (130/0 fwd/non-fwd)
 Default network 0.0.0.0/0
 Table id 0, 0 resets
 Database epoch: 1 (130 entries at this epoch)
Heimdal#<input>sh ip cef</input>
Prefix               Next Hop             Interface
0.0.0.0/0            172.16.4.1
0.0.0.0/32           receive
172.16.4.0/24        attached             Vlan1
172.16.4.0/32        receive
172.16.4.1/32        attached             Vlan1
172.16.4.5/32        attached             Vlan1
172.16.4.15/32       attached             Vlan1
172.16.4.16/32       attached             Vlan1
172.16.4.20/32       receive
172.16.4.22/32       attached             Vlan1
172.16.4.233/32      attached             Vlan1
172.16.4.254/32      attached             Vlan1
172.16.4.255/32      receive
192.168.22.0/24      172.16.4.16
192.168.128.0/24     attached             Vlan10
192.168.128.0/32     receive
192.168.128.1/32     receive
192.168.128.255/32   receive
192.168.130.0/24     attached             Vlan12
192.168.130.0/32     receive
192.168.130.1/32     receive
192.168.130.126/32   attached             Vlan12
192.168.138.149/32   attached             Vlan20
192.168.138.255/32   receive
192.168.140.0/24     attached             Vlan22
<notice>...OUTPUT OMITTED...</notice>

Adjacency table

SW1#<input>show adjacency</input>
Protocol Interface                 Address
IP       Vlan1                     172.16.4.5(7)
IP       Vlan1                     stella.tekkom.dk(7)
IP       Vlan1                     mars(9)
IP       Vlan1                     172.16.4.50(9)
IP       Vlan1                     172.16.4.60(9)
IP       Vlan1                     172.16.4.66(7)
IP       Vlan12                    192.168.130.126(7)
IP       Vlan12                    hot-pc-gf.tekkom.local(7)
IP       Vlan28                    192.168.146.145(7)
IP       Vlan28                    192.168.146.146(7)
IP       Vlan28                    192.168.146.149(7)
IP       Vlan28                    192.168.146.150(7)
IP       Vlan28                    192.168.146.151(7)

Looking at details 

SW1#<input>show adjacency 172.16.4.16 detail</input>
Protocol Interface                 Address
IP       Vlan1                     mars(9)
                                   0 packets, 0 bytes
                                   epoch 0
                                   sourced in sev-epoch 4874
                                   Encap length 14
                                   <notice>0007E9400ABF</notice>0019E75108C00800
                                   ARP
SW1#<input>sh arp | inc 172.16.4.16</input>
Internet  172.16.4.16             1   <notice>0007.e940.0abf</notice>  ARPA   Vlan1

Notes

If you enable CEF and then create an access list that uses the log keyword, the packets that match the access list are not CEF switched. They are fast switched. Logging disables CEF.

http://www.cisco.com/en/US/docs/ios/12_2/switch/configuration/guide/xcfcef.html


Links

Etherchannel operation

Common Etherchannel problems

Inconsistensies between the physical ports that are member of a channel

  • Must have same speed, duplex, trunk or access port status.
    • Same native VLAN when trunking
    • Same access VLAN when access port

Log message

%EC-5-CANNOT_BUNDLE2

Inconsistensies between the ports on the opposite sides of the EtherChannel link

If the switch on the other side is not configured to a etherchannel by discovering inconsistencies in the spanning tree.

Log message

%SPANTREE-2-CHNL_MISCFG

Uneven distribution of traffic between EtherChannel bundle members

See EtherChannel#Distributing_traffic_in_the_EtherChannel

Show commands

  • show etherchannel summary
  • show etherchannel 1 detail

Troubleshooting SVI and Inter-VLAN Routing

First HOP Routing Protocols

Verifying FHRP Operation

HSRP

  • See HSRP
  • show standby brief
  • show standby fa0/0
  • debug standby terse

VRRP

  • See VRRP
  • show vrrp brief

GLBP

  • See GLBP
  • show glbp brief
Retrieved from "http://mars.merhot.dk/w/index.php?title=CCNP_TSHOOT_Learning_Guide/Chapter_4&oldid=12350"