HSRP

From Teknologisk videncenter
Revision as of 12:14, 4 May 2009 by Heth (talk | contribs) (→‎Purpose of HSRP)
Jump to: navigation, search

HSRP or Hot Standby Router Protocol is a protocol defined by Cisco and now described in rfc2281. HSRP is a Cisco-proprietary protocol.

Purpose of HSRP

The purpose of HSRP is to ensure network connectivity in case of Router or access circuit failure, by having one standby Router waiting to take over from the failing active Router.

  • There can be only one active Router
  • There can be only one standby Router
  • There can more routers in Speak state waiting to be standby Router.

Other high availability Router protocols

How does HSRP work

HSRP works by two or more Routers agreeing upon which Router serves the virtual Router.

HSRP Protocol

HSRP runs on top of UDP, and uses port number 1985. Packets are sent to multicast address 224.0.0.2 with TTL 1.

The Virtual Router

The Virtual Router is a MAC-address and a IP Address the active Router serves beside its configured IP address. If the active Router fails one of the standby Routers becomes the Virtual Router by serving the virtual MAC-address and IP Address.

HSRP example

In picture 1 three Routers R1,R2 and R3 are setup in a HSRP Group. The Virtual IP address 10.0.0.1 and virtual MAC-Address 00-10-0C-07-AC-0A are served by the active Router R1. R1 continuesly transmits hello packets to the standby Routers.
If the Active Router fails one of the standby Routers will become the active Router and start serving the Virtual IP address 10.0.0.1 and the virtual MAC-address 00-10-0C-07-AC-0A.

There are no load balancing between the Routers.

Picture 1: HSRP group with Router R1 active and Router R2 and R3 as standby Routers

Configuration of R1, R2 and R3

hostname R1
!
interface FastEthernet1/0  
  ip address 10.0.0.11 255.0.0.0
  standby 10 priority 130 
  standby 10 preempt 
  standby 10 timers 2 6
  standby 10 ip 10.0.0.1

hostname R2
!
interface FastEthernet1/0 
  ip address 10.0.0.12 255.0.0.0
  standby 10 priority 120 
  standby 10 preempt 
  standby 10 timers 2 6
  standby 10 ip 10.0.0.1

hostname R3
!
interface FastEthernet1/0 
  ip address 10.0.0.13 255.0.0.0
  standby 10 priority 110 
  standby 10 preempt
  standby 10 timers 2 6 
  standby 10 ip 10.0.0.1

HSRP Group number

All the Routers in a HSRP Group must use the same Group number. In the example the Routers uses Group number 10. The group number ranges from 0 - 255. (Default is 0)

The virtual MAC-address

The virtual MAC-address is divided into three fields. In the example 00-10-0C-07-AC-0A

  • 00-10-0C is the vendor code. (Cisco for example)
  • 07-AC is a well-known HSRP code
  • 0A is the HSRP group number 10 decimal is 0A hexadecimal

Priority

The priority are used to decide which Router should be the active Router and in which order the standby Routers will take over. The priority field can range from 0 - 255. (Default is 100)
If more Routers has the same priority the Router with the highest configured IP address will become the active Router.

Preempt

If a Router with a higher priority becomes operative in the HSRP group, the active Router will continue to be active regardless of the new Router having a higher priority. To have the new Router with the higher priority to take over operation as the active Router use the preempt statement.

Hello timers

HSRP Routers sends hello packets at regular intervals to each other.

  • Hello packets are sent default every 3 second (Hello interval)
  • Holdtime is default 10 seconds. (Time should be at least three times hello interval)
  • Hello interval and holdtime could be learned by a standby Router from the active Router.

Tracking access Interfaces

It is important to track the access interfaces.See Picture 2 below. Under normal operations where both WANS between the buildings are operational the active router routes packets between the buildings. If the WAN connected to the active Router fails the active Router should withdraw as active Router and let the standby Router take over. See Picture 3. Thats called tracking interfaces'

Picture 2: Normal operation
Picture 3: New active Router based on tracking WAN

Configuring load balancing with HSRP

In the example below R1 will Route packets from VLAN 11 and VLAN 13 and R2 will Route packets from VLAN 10 and VLAN 12. If one of the routers fail, the other will take over. Interface tracking is configured as well. 

hostname R1
!
interface FastEthernet0/0.10
 encapsulation dot1Q 10
 ip address 172.16.10.10 255.255.255.0
 no snmp trap link-status
 standby 10 ip 172.16.10.1
 standby 10 preempt
 standby 10 priority 100
 standby 10 track Serial0/0 20
!
interface FastEthernet0/0.11
 encapsulation dot1Q 11
 ip address 172.16.11.10 255.255.255.0
 no snmp trap link-status
 standby 11 ip 172.16.11.1
 standby 11 preempt
 standby 11 priority 110
 standby 11 track Serial0/0 20
!
interface FastEthernet0/0.12
 encapsulation dot1Q 12
 ip address 172.16.11.10 255.255.255.0
 no snmp trap link-status
 standby 12 ip 172.16.12.1
 standby 12 preempt
 standby 12 priority 100
 standby 12 track Serial0/0 20
!
interface FastEthernet0/0.13
 encapsulation dot1Q 13
 ip address 172.16.13.10 255.255.255.0
 no snmp trap link-status
 standby 13 ip 172.16.13.1
 standby 13 priority 110
 standby 13 preempt
 standby 13 track Serial0/0 20
Picture 4: Configuring Load balancing using VLAN's
 
hostname R2
!
interface FastEthernet0/0.10
 encapsulation dot1Q 10
 ip address 172.16.10.20 255.255.255.0
 no snmp trap link-status
 standby 10 ip 172.16.10.1
 standby 10 preempt
 standby 10 priority 110
 standby 10 track Serial0/0 20
!
interface FastEthernet0/0.11
 encapsulation dot1Q 11
 ip address 172.16.11.20 255.255.255.0
 no snmp trap link-status
 standby 11 ip 172.16.11.1
 standby 11 preempt
 standby 11 priority 100
 standby 11 track Serial0/0 20
!
interface FastEthernet0/0.12
 encapsulation dot1Q 12
 ip address 172.16.11.20 255.255.255.0
 no snmp trap link-status
 standby 12 ip 172.16.12.1
 standby 12 preempt
 standby 12 priority 110
 standby 12 track Serial0/0 20
!
interface FastEthernet0/0.13
 encapsulation dot1Q 13
 ip address 172.16.13.20 255.255.255.0
 no snmp trap link-status
 standby 13 ip 172.16.13.1
 standby 13 priority 100
 standby 13 preempt
 standby 13 track Serial0/0 20
Retrieved from "http://mars.merhot.dk/w/index.php?title=HSRP&oldid=5402"